Test data Journal rotation test <Testing conditions> Bearing dimension : 035X038X R 20 Pressure : 0.39N/mm2|4.0kgf/cm2| is added every 5minutes Lubrication : grease is applied at the time of assembly • Serviceable without the need for lubrication. • Has superior load resistance and wear resistance. • Features low coefficient of friction and superior speed characteristics. • Prevents stick slips and squeak noises. • Injection-molded and can be made in complicated shapes. Good mass productivity. • Standard products and materials for machining are available in various sizes. • For a low volatile organic compound type, Oiles 80-LVF is available on order. Service range >8 These are values of the typical grade Oiles 80. Attention should be paid to dimensional variances due to thermal expansion, chucking, and bend of the material. ^ Contact us for grinding and milling information. >8 The values shown above are typical values, not the standard values. (Note) Excludes 80M, 80P, 80S and 80-LVF. Lathe turning Machining accuracy (bushing) Classes here are in JIS standard. This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5pm. Dimensions may change due to thermal expansion, chucking pressure, moisture absorption deformation, etc. High accuracy is ensured if the product is installed on the housing and then ground. Journal oscillation test_ <Testing conditions> Bearing dimension : 040X050X R 30 Mating material : S45C Oscillating cycle : 72cpm Oscillating angle : 24° Lubrication : grease is applied at the time of assembly Thrust rotation test_ <Testing conditions> Journal rotation test_ <Testing conditions> Bearing dimension : 010X014X110 Mating material : SUJ2 (surface roughness approx. Ra0.1 pm) Test time[hrsj

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing Multi-layer Bearing ^R[g|R|RQeaBEE^I Information Selection Guide Oiles 80 Bushings 1510 a: Chamfering for O.D. b: Chamfering for I.D. Mating shaft ,★ Mark products have *: O.D. chamfering for the bushing I.D. of 06 or smallermm) • The Oiles 80 bushings are injection-molded. • The inner diameter tolerances are the values after pressing into a ring gauge of 0 D ±0.002. • A stopper is needed at the temperature of 0°C or less, since the bushing is dislocated due to thermal shrinkage. The dimensional tolerances...

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing Multi-layer Bearing ^R[g|R|RQeaBEE^I Information Selection Guide Oiles 80 Flange Bushings 1510 Part No.Mating shaft 0.8/ Flange bushing Housing , ★ Mark products have Product Technical Selection Guide Information Multi-layer Bearing Metallic Bearing Air Bearings Slide Shifter Information Corporate Profile

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing Multi-layer Bearing Information Selection Guide 80W isher • “If the mating part has coarse surface” “If foreign matter may be put on the bearing surface” “If the coefficient of friction should be especially low” The “plain washers” specified in JIS B1256 may be used as the mating part. In the above cases, however, plastic-to-plastic sliding with overlapped the 80W and 83W is effective. • It is recommended to apply multi-purpose lithium grease of consistency NLGI grade 2 to 0. 83W isher Specify Part No....

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing Multi-layer Bearing Information Selection Guide 80P Oiles 80 Plate Material Part No. Product Technical Selection Guide Information ^RflggRnHgggRnQ^H Multi-layer Bearing Metallic Bearing Air Bearings Slide Shifter Information Corporate Profile

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing Multi-layer Bearing Information Selection Guide 80S Oiles 80 Pipe Stock Feature • Has the same features as 80. • Demonstrates superior sliding performance in sliding motion. • The whole bearing unit is made of plastic. Small, lightweight, and superior corrosion resistance. • The standard products are available in various sizes. Service range

Technical Product Corporate Profile Information Slide Shifter Air Bearings Metallic Bearing Multi-layer Bearing ^R[g|R|RQeaBEE^I Information Selection Guide 80FL Oiles Pillow 80 Flange Units • The recommended shaft dimension and finishing grade are h7 and Rz3.2gm or less, respectively. The shaft dimension of e7 is recommended if used at the temperature of 0°C (32°) or less. • Apply grease or oil to the sliding surface. • Use bolts and washers to mount the product. • The allowable tightening torques shown in parentheses are the values if no washer is used. • Find the surface pressure from the...