T308E ELECTRIC MATERIAL HANDLER 75 YEARS OF EXPERIENCE, A DRIVING FORCE, DESIGNED FOR THE FUTURE

ELECTRIC MATERIAL HANDLER Pure energy by your side

Mode 1 > Power saving When this function is enabled, the material handling machine is set to a low rpm value to consume as little energy as possible. Therefore, its movements will be slower but more accurate. The power saving mode is suitable for belt loading, hopper filling or mid-air loading. In this way, the battery life will be extended as far as possible. . Mode 2 > Balanced consumption When this function is enabled, the material handler's energy consumption is optimised and all the movements, from travel to boom operation, are balanced. In this mode, the working speed is enough to carry...

HIGH EFFICIENCY BY YOUR SIDE >POWER ENERGY High driving charge The T308E material handler is powered by 2 batteries housed in special compartments placed at the back of the swing drive that acts as a counterweight. The 960Ah/80V batteries are connected in parallel and are equipped with voltage reducers for the auxiliary circuits. Two electronic Inverters control the motor that drives the main hydraulic pump and the auxiliary pump. Two high-frequency electronic battery chargers included, with high charging efficiency.

DRIVING FORCE >CONTROL AND COMFORT The control cab of the T308E provides all the comfort of a standard cab installed on diesel engine machines. The interior of the T308E cab is spacious, properly illuminated and all the controls can be easily accessed. As a standard feature, the cab can be raised slightly but, on request, it can be equipped with a scissor lifting system with controlled suspension that will allow the operator to obtain a view from a height of up to 5,3 metres from the ground. The dashboard contains all the machine function keys and displays that show the battery charging status...

EQUIPMENT > STANDARD < OPTIONAL > Intermediate rubber rings < Air conditioning with air-prefiltering > Two-pieces boom with secondary one monolithic, total length 7,5 m

Rotation center ELECTRIC MATERIAL HANDLER DIAGRAM OF MOVEMENTS All load values are specified in tonnes (T) and apply at the end of the half-boom, without any gripping device installed, on firm, level ground. The values indicated correspond to 75% of the tipping load or 87% of the hydraulic lifting force, according to ISO 10567. The load ratings in brackets [], with a locked swing axle, refer to a stabilisation set-up on tyres (with stabilisers raised) and 360° turret rotation. NOTE: Data and weights are indicative and not binding: Tabarelli reserves the right to make any modifications it deems...

All load values are specified in tonnes (T) and apply at the end of the half-boom, without any gripping device installed, on firm, level ground. The values indicated correspond to 75% of the tipping load or 87% of the hydraulic lifting force, according to ISO 10567. The load ratings in brackets [], with a locked swing axle, refer to a stabilisation set-up on tyres (with stabilisers raised) and 360° turret rotation. NOTE: Data and weights are indicative and not binding: Tabarelli reserves the right to make any modifications it deems appropriate.

T308E ELECTRIC MATERIAL HANDLER Rotation center DIAGRAM OF MOVEMENTS All load values are specified in tonnes (T) and apply at the end of the half-boom, without any gripping device installed, on firm, level ground. The values indicated correspond to 75% of the tipping load or 87% of the hydraulic lifting force, according to ISO 10567. The load ratings in brackets [], with a locked swing axle, refer to a stabilisation set-up on tyres (with stabilisers raised) and 360° turret rotation. NOTE: Data and weights are indicative and not binding: Tabarelli reserves the right to make any modifications it...

MOTOR Type Batteries Motor speed (RPM) adjustment HYDRAULIC SYSTEM Main pump Delivery rate Max operating pressure Adjustment Heat exchanger Filtering Hydraulic tank capacity SLEWING DRIVE Engine Gearbox Slewing ring Slewing speed Main cross-motion servo-controls Shift Auxiliary Movements Control Electric motor with alternating current power of 1X50kW selector switch with 4 operating modes variable displacement axial-piston pump 180 l/min 280 Bar Electro-hydraulic controls water/oil element side by side with by-pass valve partial return to the tank 215 l with axial pistons The gearbox is comprised...

BOOM Structure Length Bushings and pins Cylinders made of high-strength steel, in 2 elements with secondary monolithic from 7.5 to 9 meters optional made of special steel for concrete single cylinder on 1st and 2nd boom with hydraulic brake WEIGHT about 19 ton in working order RECOMMENDED Grab for waste model RR560 with 5 blades EQUIPMENT Grab for scrap model RV320 with 6 blades SOUND LEVEL NOISE REDUCTION (Dir 2000/14/CE - 2005/88/CE) Sound pressure level at driving position LpA 77 dB (A) MOVEMENT METER MACHINERY DIRECTIVE (Dir 2006/42/CE) Electronic monitoring device for the stability of the...

VIA CARLO ALBERTO DALLA CHIESA, 2 37060 - MOZZECANE (VR) - ITALY TEL. +39 045 7930007 FAX +39 045 7930214 [email protected] WWW.TABARELLI.COM OFFICINA MECCANICA F.LLI TABARELLI S.P.A.