Electronically Controlled Pneumatic Pincer
Electronically Controlled Pneumatic Pincer
- ELK 02 Control Unit: Operates on a power supply of 85–265 V / 47–63 Hz, requires 30 Va, and supports a compressed air supply of 4–10 bar. It integrates with automated systems via USB, RS232, and other ports.
- Pincer Systems: Various models (HO 2000 EL, HO 3000 EL, etc.) are available with specific jaw widths and open gaps to accommodate different ear widths. The pincers are compatible with different plug types for global use.
- Installation: The document outlines steps for selecting and using the correct pincer head and type based on the clamp type, required closing force, and air pressure. It emphasizes setting the correct closing force using a tester like the CAL 01.
- Selection: Users must choose the appropriate pincer head and type (EL or ELT) based on clamp requirements. Item numbers are provided for ordering complete pincer systems and replacement kits.
- Ensure the jaw width is at least 0.5 mm wider than the band used for clamps.
- The opening gap should accommodate the largest ear size.
- Special pincer heads are available for restricted access areas, with options for angled jaws at 30° and 60°.
- Jaw widths range from 5.5 mm to 14.5 mm, with corresponding open gaps and ear width compatibility.
- Item numbers are provided for each pincer type and configuration, facilitating easy ordering and replacement.
Catalog excerpts
Electronically Controlled Pneumatic Pmcer Connecting Technology
Open the catalog to page 1
Installation of Ear Clamps and Low Profile Clamps Control Unit with Trigger unit EL (EL = electronic version) or with Trigger unit ELT ergonomic handling (ELT = electronic version with extended trigger) Highly efficient, verified installation Process reliability, electronic monitoring of all specified parameters – 100% documentation Prevention of multiple closures by means of clamp detection in the pincer head Up to 99 parameter data sets (APN) programmable Optimal usability with the aid of function keys and large display Force or stroke-priority action, either with or without initial holding...
Open the catalog to page 2
Installation of Ear Clamps and Low Profile Clamps Technical data ELK 02 control unit Delivery scope ELK 02 control unit Power supply: 85-265 V / 47-63 Hz Control unit item no. 13600289 Power requirement: 30 Va (Fuse 10 A) PC Software ELK 02 Compressed air supply: 4-10 bar CD with operating instructions External dimensions: 200 x 230 x 70 mm Compressed air connection set (incl. filter/water separator) Weight: 3.7 kg Connection cable for all interfaces Mains cable with country-specific plug Selection of control unit Plug type Schuko plug (plug type F, 3-pole)...
Open the catalog to page 3
Installation of Ear Clamps and Low Profile Clamps Selection of complete pincer systems The complete pincer system consists of pincer head and pincer. 1) First select the pincer head in accordance with the requirement. 2) Then select the pincer type (EL or ELT) in the corresponding columns below. The item numbers for the complete pincer include the pincer and the desired pincer head. Pincer heads Jaw width (mm) 5.5 7.5 7.5 10.2 10.2 10.5 10.5 14.5 * measured inside Type of pincer Standard trigger unit EL Type of pincer Standard Trigger unit ELT with extended trigger ELT...
Open the catalog to page 4
Installation of Ear Clamps and Low Profile Clamps Technical data Pincer heads Jaw width (mm) 5.5 7.5 7.5 10.2 For ear width* (mm) = 7 8 10 8 Item No. 13900156 13900152 13900148 13900144 Type of pincer HO 2000 EL HO 3000 EL HO 4000 EL Pincer heads Jaw width D (mm) For ear width* (mm) Item No. Pincer heads Jaw width D (mm) For ear width* (mm) Item No.
Open the catalog to page 5
Installation of Ear Clamps and Low Profile Clamps Installation tool with high process reliability Efficient, uniform assembly High-quality, complete pincer system for uniform clamp closures Full range of pincer heads, for compatibility to all standard clamps Adaptation of special head designs possible Pneumatic Pincers Oetiker ME This high-quality, complete pincer system ensures the uniform installation of Oetiker clamps. The selection of the correct pincer body and head is dependent on the type of Oetiker clamp, the required closing force, and the air supply pressure that is available. To obtain...
Open the catalog to page 6
Installation of Ear Clamps and Low Profile Clamps Delivery scope pneumatic pincer Oetiker ME Oetiker ME with pincer head Compressed air connection set (incl. filter/water separator) Operating instruction Selection of complete pincer systems The complete pincer system consists of pincer head and pincer. 1) First select the pincer head in accordance with the requirement. 2) Then select the pincer type in the corresponding columns below. The item numbers for the complete pincer include the pincer and the desired pincer head. Pincer heads Jaw width (mm) 5.5 7.5 7.5 Open gap (mm) 8.6 11.6 13.2...
Open the catalog to page 7
Installation of Ear Clamps and Low Profile Clamps Technical data HO 2000 ME/HO 3000 ME/HO 4000 ME Pincer heads Jaw width D (mm) 5.5 7.5 7.5 10.2 HO 3000 ME A (mm) B (mm) C (mm) D (mm) E (mm) F (mm) HO 4000 ME A (mm) B (mm) C (mm) D (mm) E (mm) F (mm) Rights to make technical changes in the interests of further development reserved.
Open the catalog to page 8
Installation of Ear Clamps and Low Profile Clamps Pincer heads Jaw width D (mm) 10.5 10.5 Pincer heads Jaw width D (mm) 10.5 10.5 * measured inside Compressed air connection: internal thread G 1/4
Open the catalog to page 9
Special Pincer Heads for Oetiker ME/EL Special Pincer Heads for Oetiker ME/EL – Installation of Oetiker Ear Clamps 1/2 Pincer head with extended holders Different extensions allow to reach areas where access is restricted. Compatible with pincer types HO 2000 to HO 4000. Selection of pincer heads The jaw width must be at least 0.5 mm wider than the band used for the clamps to be installed. The opening gap should be wide enough for the largest ear. Pincer heads Jaw width D (mm) 5.5 7.5 Open gap (mm) 8.6 13.2 Height E (mm) 11.0 12.0 For ear width* (mm) =7 10 Type of pincer HO ME Pincer head...
Open the catalog to page 10
Special Pincer Heads for Oetiker ME/EL Pincer heads with angled jaws Specially for installing ear clamps where access is restricted. Suitable for ear clamps with 7 and 9 mm band widths. Compatible with pincer types HO 2000 to HO 4000. Pincer heads 30° Jaw width (mm) 10.2 Type of pincer HO ME Pincer head complete 13900706 HO EL Pincer head complete 13900707 Replacement-jaw kit 13900708 Pincer heads 60° Jaw width (mm) 10.2 Type of pincer HO ME Pincer head complete 13900694 HO EL Pincer head complete 13900697 Replacement-jaw kit 13900695 Measured inside
Open the catalog to page 11
Special Pincer Heads for Oetiker ME/EL Special Pincer Heads for Oetiker ME/EL - Installation of Oetiker Ear Clamps 2/2 Jaws angled at 45° Compatible with pincer types HO 2000 to HO 4000. Jaws angled at 45° Compatible with pincer types HO 5000 and HO 7000. Pincer heads 45° Jaw width (mm) 10.2 10.2 Type of pincer HO ME Pincer head complete 13901271 13900775 Pincer heads 45° Jaw width (mm) 14.5 14.5 Type of pincer HO ME Pincer head complete 13900784 13900782 Jaws angled at 90° Compatible with pincer types HO 2000 to HO 4000. Pincer heads 90° Jaw width (mm) 10.2 10.2...
Open the catalog to page 12
Special Pincer Heads for Oetiker ME/EL 90° lengthwise Compatible with pincer types HO 2000 to HO 4000. Pincer heads 90° lengthwise Jaw width (mm) 7.5 7.5 Type of pincer HO ME Pincer head complete 13901280 13901282 Pincer Head for 1-Ear Clamp with stud Pincer head for installation of 1-Ear Clamp with stud, band width 14 mm. Compatible with pincer types HO 5000 and HO 7000. Pincer heads Jaw width (mm) 14.5 Type of pincer HO ME Pincer head complete 13900773 HO EL Pincer head complete 13900772 Replacement-jaw kit 13900771 Measured inside
Open the catalog to page 13All OETIKER catalogs and technical brochures
Hand Tubing Cutters3 Pages
Pistol grip3 Pages
Oetiker CP 10, -204 Pages
Oetiker Quick Connectors13 Pages
PEXGrip2 Pages
ToothLock® Ear Clamps 2936 Pages
HO 10000 ELT - ELK023 Pages
Test Equipment6 Pages
Compact_Compact XL4 Pages
Swaging tools8 Pages
PG 2004 Pages
Clamps ER4 Pages
1-Ear and 2-Ear Clamps6 Pages
Adjustable Clamps6 Pages
Connecting Solutions122 Pages
Quick Action Couplings SV28 Pages
Swing Couplings SC28 Pages
Catalogue106 Pages
- Calibration system
- Crimping applicator
- Hose clamp
- Crane scale
- Manual crimping tool
- Stainless steel hose clamp
- Band hose clamp
- Screw band clamp
- Strap
- T-Bolt hose clamp
- Connector crimping tool
- Battery-operated crimping tool
- Steel hose clamp
- Manual cutting device
- Wing hose clamp
- Swaging machine
- Adjustable ear type hose clamp
- Rugged hose clamp
- Heavy-duty hose clamp
- Pneumatic calibrator