FRS SERIES General Features The rotary limit switch Driver FRS Series is a device used to control the movement of construction machines and industrial machines in general. It is connected via its shaft to a motor in a manner that, after a programmed number of revolutions, the cams cause the intervention of the internal contacts. The adjustment of the cams, innovative and precise, allows to determine the point of operation of the microswitches in a linear and micrometric. There is a wide range of gear ratios and alternatively you can mount a series of sensors corner which realize multiple linear outputs. The contacts are in positive opening (EN 60947-5-1) in order to increase the safety of the people. A large number of accessories completes the range of the limit switch, facilitating its use. Directive conformity CEE 2006/42/CE 2011/65/UE Rules conformity EN 60947-1 EN 60947-5-1 EN 60204-1 EN 60529 EN 60439-1 Insulation Voltage 250V~ Maximum Voltage 250V~ Base black nylon additive Cover yellow thermoplastic high mechanical and thermal resistance Operating Temperature -20 °C + 60 °C -40 °C + 60 °C (on request) Worm transmission Standard cable input: 1 cable gland M16 x 1,5 Protection Degree IP 65 Protection against contact voltages on double insulation Maximum rpm 500 CE omologation Weight about 300 gr (2 contact model) Made in Italy product – patented shape 1 Nuova CEVA Automation. Via G.B. Signini 43. Briga Novarese (NO) ITALY Tel. +39 0322 93574 Fax +39 0322 953787 i

FRS SERIES Contacts and Regulations Cam Each cam is equipped with its own adjusting screw micrometer. The adjustment is made simply using a screwdriver. 1. Adjusting fast optional • loosen the screw top • rotate hand cams • tighten the top screw (1 Nm torque) 2. Fine adjustment • turn the adjusting screw for each cam • Recommended screwdriver 4.0 x 0.8 The particular system of clutch, ensures rapidity and precision of regulation and guarantees stability, consistency and reliability in time. Contacts Technical Features                Microswitch contact (on request) Rules conformity...

FRS SERIES Standard Executions Codes to order, the product code is made up as follows: B FRS XXX Y N Contact number (2-3-4) Contact model (R-D) Reduction Ratio If not further specified, the limit switches are supplied with the lever type A. For any use of levers different from type A, use the bottom of the code: B / C / D / E / F The experience gained and shared with many manufacturers of position sensors allowed us to achieve the necessary interfaces to fit various sensors of different brands, according to the demands of our customers, as an alternative to contacts. Standard reduction ratio...

FRS SERIES For your safety Requirements for installation and maintenance INSTALLATION AND WIRING The installation of the limit switch FRS series Drivers must be performed by qualified personnel, in compliance with current safety standards. Before wiring is mandatory cut power to the machine and put it safely. For proper installation predict Operating ambient temperature between -20 ° C and + 60 ° C. The switch is not suitable for use in potentially explosive, corrosive or with high content of sodium chloride. Acids, oils and solvents may degrade the device; the limit switch is lubricated "for...

FRS SERIES Spare parts and accesories Fast contact R 1NA/1NC white Gold contact D 1NA/1NC Cover for 2 micro Cover for 3-4 micro Code BCAMAFR BCAMBFR BCAMCFR BCAMDFR BCAMEFR BCAMFFR Code BFLANFRM BAFLESFC BINNFC - Description Cam A – spike Cam B – sector Cam C – quarter Cam D – half turn Cam E – circular Cam F – 10 spike Description Flange Flexible shaft Male joint Potentiometer (on request) Other sensor (on request) Plastic support (on request) 5 Nuova CEVA Automation. Via G.B. Signini 43. Briga Novarese (NO) ITALY Tel. +39 0322 93574 Fax +39 0322 953787 i