Catalog excerpts
Super Tite-Lock Milling Chucks CAT/CT- S Center-through coolant feeding is possible. New Generation Milling Chucks Two-stage tightening Unique retaining ring allows high speed milling Improved durability is ensured by our perfect seal mechanism ¡Special design slits in bore High rigidity type Circlip Rubber seal Special resin seal Special resin seal œStage one Finish milling:Tighten clamping ring till the black ring is not visible. œStage two Heavy milling:Completely tighten clamping ring to achieve maximum gripping torque . Clamping completed Before clamping T-slit Deep groove slit High balance type CTS-E Slim type High retentivity High rigidity New improved seal design reduces contamination and minimizes maintenance. Caution: Please rotate the clamping ring counterclockwise more than one time after a cutting tool is removed. For collet through coolant with MC-C collet For cutters with coolant hole CTS New patented“T-slit”design minimizes slippage and pull out of end mill. (CTS-E) High balanced
Open the catalog to page 12-Air holes Back-up Screw (Optional) G l D l2 L d Back-up Screw (Optional) G 2-Air holes d1 L0 L l2 l1 l d D L1 G 2-Air holes Back-up Screw (Optional) l2 l d D D1 L2 L Type 1 Type 2 Type 3 Ordering Example BT40-CT25S-120 Caution Type2 Possible A.T.C. interference on milling chucks. Please check comparison dimensions again st A.T.C. manufacturers specifications. When ordering, indicate the number of spanner wrenches required. “No charge” spanner wrenches are limited to the number of milling chucks on order. Extra spanner wrenches can be purchased separately. (See page 24) Two M4×5(S)...
Open the catalog to page 52-Air holes Back-up Screw (Optional) G l D l2 L d Back-up Screw (Optional) G 2-Air holes d1 L0 L l2 l1 l d D L1 G 2-Air holes Back-up Screw (Optional) l2 l d D D1 L2 L Type 1 Type 2 Type 3 Ordering Example BT40-CT25S-120E Caution Type2 Possible A.T.C. interference on milling chucks. Please check comparison dimensions again st A.T.C. manufacturers specifications. When ordering, indicate the number of spanner wrenches required. “No charge” spanner wrenches are limited to the number of milling chucks on order. Extra spanner wrenches can be purchased separately. (See page 24) Two M4×5(S)...
Open the catalog to page 9All NT Tool catalogs and technical brochures
-
Power Hydro Chuck
13 Pages
-
Collet Type Floating Holder
2 Pages
-
BCL - BT Clamper
1 Pages
-
UTS series
36 Pages
-
HSK-T series
8 Pages
-
HSK serires
85 Pages
-
AHO series
42 Pages
-
CAT series
55 Pages
-
BT series
142 Pages
-
HSK Clamper
1 Pages
-
Slim Hydro Chuck PHC·S
8 Pages
-
General Catalog
586 Pages
-
OTP Optical Tool Presetter
6 Pages
-
"R"- ZERO HOLDER
9 Pages
-
ZERO MASTER / ZM-1
1 Pages
-
MORSE TAPER ADAPTERS / MTA
2 Pages
-
TAP HOLDERS / TP3B
2 Pages
-
EASY PRESET SERIES / STM
11 Pages
-
SHRINKFIT HOLDERS / SRE
8 Pages
-
ER COLLET CHUCKS / ERC
12 Pages
-
HDC COLLET CHUCKS / HDC-A
7 Pages
-
GDC COLLET CHUCKS / GDC
4 Pages
-
R-ZERO SETTER / SPZ-2
1 Pages
-
EASY PRESET SERIES / SDM
7 Pages
-
Straight Drill Chuck
7 Pages
-
HSK Tightening Fixture
2 Pages
-
Simple Setter
7 Pages
-
Side Lock Holders
8 Pages
-
Jacobs Taper Arbors
2 Pages
-
High Precision Coolant Collets
10 Pages
-
Chamfering Cutter Series
4 Pages
-
Quick Change Stub Tapper
4 Pages
-
Quick Change Stub Holder
5 Pages
-
Milling Chuck Collets
13 Pages
-
Contactless Tool Presetter
6 Pages
-
Coolant Inducer
4 Pages
-
Hyper Spindle
3 Pages
-
Angle Heads
7 Pages
-
Keyless Drill Chucks
2 Pages
-
Synchronous Tap Holder
11 Pages
-
Shrink-Fit Holders
8 Pages
-
Heating Device
3 Pages
-
R-Zero collet chucks
9 Pages