Catalog excerpts
Easy Tool Length Adjustment Synchronous Tap Holder Easy Tool Length Adjustment Improvement of work ability Preset screw 1 Tap projection length can be adjusted easily by turning the guide ring. 2.Center-through coolant feeding enabled (Max. 5-7MPa). 3.Slippage of tap can be prevented by preset drive. 4Tap size can be changed by replacing preset drivers and collets. Preset driver (option) Tool length is adjustable by rotating this guide ring. For longer projection length Center through feeding enabled ■Internal coolant feeding enabled. Maximum coolant pressure: Tool shank diameter 19mm and smaller : 7MPa *coolant collet is optional *Two types (high pressure and low pressure type) FSC-OH type through coolant FSC-C type
Open the catalog to page 1Synchronous Tap Holder Easy Tool Length Adjustment Preset Driver
Open the catalog to page 2Synchronous Tap Holder Easy Tool Length Adjustment 1. Collet, preset driver and spanner are sold separatey. 2. Please referto P120 for £i dimension. 3. STM8 can be used for tap holes smaller than M4. Collet size is as below. Tap drive cannot be used for the above usages. Fig. 1 Coolant leakage happens Tool insertion length
Open the catalog to page 3Synchronous Tap Holder Easy Tool Length Adjustment Preset Driver
Open the catalog to page 4Synchronous Tap Holder Easy Tool Length Adjustment Preset Driver 1. Collet, preset driver and spanner are sold separatey. 2. Please referto P120 for E1 dimension. 3. Tap holes smaller than M4 can be made by STM8 or HDC07. Collets to be used are as follows. Tap drive will not be used for the above usages. 4. When central coolant feeding is intended by using the coolant collet, straight shank of the tapmust be inserted deep enough to cover the whole length of the collet. In case tap's square is in the collet ID, coolant may leak from the slits. Always keep the tap's square part out of the...
Open the catalog to page 5Synchronous Tap Holder Easy Tool Length Adjustment Tapping Capacity
Open the catalog to page 6Synchronous Tap Holder Easy Tool Length Adjustment Tapping Capacity 1. Collet, preset driver and spanner are sold separatey. (P55 - 61,119 -122) 2. Please refèrto P120 for S dimension. 3. Tap holes smaller than M4 can be made by STM8 or HDC07. Collets to be used are as follows. Tap drive will not be used for the above usages. 4. When central coolant feeding is intended by using the coolant collet, straight shank of the tap must be inserted deep enough to cover the whole length of the collet. In case tap's square is in the collet ID, coolant may leak from the slits. Always keep the tap's...
Open the catalog to page 7Synchronous Tap Holder Easy Tool Length Adjustment
Open the catalog to page 8Synchronous Tap Holder Easy Tool Length Adjustment • OH type collet should be used for center-through coolant feeding and external coolant feeding. • when "collet-through" coolant
Open the catalog to page 10Synchronous Tap Holder Easy Tool Length Adjustment
Open the catalog to page 11All NT Tool catalogs and technical brochures
-
Power Hydro Chuck
13 Pages
-
Collet Type Floating Holder
2 Pages
-
BCL - BT Clamper
1 Pages
-
UTS series
36 Pages
-
HSK-T series
8 Pages
-
HSK serires
85 Pages
-
AHO series
42 Pages
-
CAT series
55 Pages
-
BT series
142 Pages
-
HSK Clamper
1 Pages
-
Slim Hydro Chuck PHC·S
8 Pages
-
General Catalog
586 Pages
-
OTP Optical Tool Presetter
6 Pages
-
"R"- ZERO HOLDER
9 Pages
-
ZERO MASTER / ZM-1
1 Pages
-
MORSE TAPER ADAPTERS / MTA
2 Pages
-
TAP HOLDERS / TP3B
2 Pages
-
SHRINKFIT HOLDERS / SRE
8 Pages
-
ER COLLET CHUCKS / ERC
12 Pages
-
HDC COLLET CHUCKS / HDC-A
7 Pages
-
GDC COLLET CHUCKS / GDC
4 Pages
-
R-ZERO SETTER / SPZ-2
1 Pages
-
EASY PRESET SERIES / SDM
7 Pages
-
Straight Drill Chuck
7 Pages
-
HSK Tightening Fixture
2 Pages
-
Simple Setter
7 Pages
-
Side Lock Holders
8 Pages
-
Jacobs Taper Arbors
2 Pages
-
High Precision Coolant Collets
10 Pages
-
Chamfering Cutter Series
4 Pages
-
Quick Change Stub Tapper
4 Pages
-
Quick Change Stub Holder
5 Pages
-
Milling Chuck Collets
13 Pages
-
Contactless Tool Presetter
6 Pages
-
Coolant Inducer
4 Pages
-
Hyper Spindle
3 Pages
-
Angle Heads
7 Pages
-
Keyless Drill Chucks
2 Pages
-
Synchronous Tap Holder
11 Pages
-
Shrink-Fit Holders
8 Pages
-
Heating Device
3 Pages
-
R-Zero collet chucks
9 Pages
-
New Generation Milling Chucks
15 Pages