Catalog excerpts
BT40-HDC16A-135CS BT40-CDC16-135 Collet Chuck Type Coolant Supply 8,000rpm 870psi R.P.M. Cutter with oil hole FDC-OH type L Completely sealed by short slotting No damage to ball bearings from coolant leakage 8,000rpm 870psi R.P.M. Cutter without oil hole FDC-C type L Effective coolant flow thru 2 coolant nozzles (grooves) Specifications Actual example at our user's Type MAX RPM MAX Coolant Weight lbs HDC07Type 8000 CT16Type 6000 290psi CT-CS 290psi Old type New type Holder Cutting conditions Service life (Length of use) Seizure of bearings Bearings will not seize. Change of seal units Revolutions 2,000rpm 145psi Coolant pressure Replaceable seal unit: The seal unit can be replaced easily for quick and low-cost maintenance of the holder. Seal Seal sleeve Seal unit NT’s fluid heads deliver coolant right to the tool tip on machines without coolant through the spindle capabilities to flush out chips and improve cutting performance. Delivers coolant right to the tool tip on machines without coolant through the spindle capabilities. Flushes out chips and improves cutting performance. Coolant at the tool tip extends tool life. Prevents tool breakage and flushes out troublesome heat and chips. NT uses multi-seal construction, sealed high speed roller bearings, and a tough corrosion resistant surface treatment for precise trouble-free operation and long life. Collet chuck Type Milling chuck Type CT-CS
Open the catalog to page 13.228 2.953 L 2.795 D2 d 1.772 1.378 D1 2.165 2.205 2.638 3.543 1.220 1.299 Part Number - - - Body Seal Sleeve 2.244 Qty 1.850 D L d Qty 1.378 1.772 2.165 Seal Sleeve 2.638 0.189 2 1.299 Seal 1 Part Number - - - L D1 d D L d Seal Body Seal Sleeve Seal Seal Sleeve Note: Seal body and seal sleeve are made as one unit. + 1. When replacing the seal unit, please purchase both the seal body and seal sleeve. 2. When replacing 2 seals only, please purchase a seal set as shown below. Note: A seal set consists of 2 seals and 1 seal sleeve made as 1 unit. Note: CT S-CS coolant inducers must be...
Open the catalog to page 4All NT Tool catalogs and technical brochures
-
Power Hydro Chuck
13 Pages
-
Collet Type Floating Holder
2 Pages
-
BCL - BT Clamper
1 Pages
-
UTS series
36 Pages
-
HSK-T series
8 Pages
-
HSK serires
85 Pages
-
AHO series
42 Pages
-
CAT series
55 Pages
-
BT series
142 Pages
-
HSK Clamper
1 Pages
-
Slim Hydro Chuck PHC·S
8 Pages
-
General Catalog
586 Pages
-
OTP Optical Tool Presetter
6 Pages
-
"R"- ZERO HOLDER
9 Pages
-
ZERO MASTER / ZM-1
1 Pages
-
MORSE TAPER ADAPTERS / MTA
2 Pages
-
TAP HOLDERS / TP3B
2 Pages
-
EASY PRESET SERIES / STM
11 Pages
-
SHRINKFIT HOLDERS / SRE
8 Pages
-
ER COLLET CHUCKS / ERC
12 Pages
-
HDC COLLET CHUCKS / HDC-A
7 Pages
-
GDC COLLET CHUCKS / GDC
4 Pages
-
R-ZERO SETTER / SPZ-2
1 Pages
-
EASY PRESET SERIES / SDM
7 Pages
-
Straight Drill Chuck
7 Pages
-
HSK Tightening Fixture
2 Pages
-
Simple Setter
7 Pages
-
Side Lock Holders
8 Pages
-
Jacobs Taper Arbors
2 Pages
-
High Precision Coolant Collets
10 Pages
-
Chamfering Cutter Series
4 Pages
-
Quick Change Stub Tapper
4 Pages
-
Quick Change Stub Holder
5 Pages
-
Milling Chuck Collets
13 Pages
-
Contactless Tool Presetter
6 Pages
-
Hyper Spindle
3 Pages
-
Angle Heads
7 Pages
-
Keyless Drill Chucks
2 Pages
-
Synchronous Tap Holder
11 Pages
-
Shrink-Fit Holders
8 Pages
-
Heating Device
3 Pages
-
R-Zero collet chucks
9 Pages
-
New Generation Milling Chucks
15 Pages