Datasheet GF380
9Pages

Data Sheets Belt Conveyors Type 398 - height 30 mm Type 397 - height 40 mm Type 360 - height 60 mm Type 380 - height 100 mm Download available on our homepage http://www.nsm-magnettechnik.com

Belt Conveyor with drum motor (E=L-150) retractable length slot nuts M8 x 10 R - electric connection right Ø123 / Ø145 / Ø174 with rubber coating when flat wire link belt (FDG) and/or v > 60 m/min * Ø113 / Ø135 / Ø164 without rubber coating defenition over application and dimension Type code: Permanent magnetic Non magnetic Nominal width (NW) Length [ 50 mm steps ]Electric connection- Revision I [dimensions and technical modifications subject to change] Drum motor with Ø113 Drum motor with Ø123 Drum motor with Ø135 Drum motor with Ø145 Drum motor with Ø164 Drum motor with Ø174 Belt quality...

Belt Conveyor with gear motor * with rubber 1 coating when flat wire link belt (FDG) and/or v > 60 m/min driving power: Type code: Revision I [dimensions and technical modifications subject to change] Permanent magnetic Non magnetic Nominal width (NW)Length [ 50 mm steps ]Drive arrangement Gear motor Frequ. contr. gear motor Belt quality Lateral guide plates Belt run control Belt speed Operating voltage please specify Standard: 230/400 V - 50 Hz - 3 Ph defenition over application and dimension * differs, depending on type of motor

Belt Conveyor with gear motor * with rubber coating when flat wire link belt (FDG) and/or v > 60 m/min (E=L-150) retractable length slot nuts M8 x 10 defenition over application and dimension driving power: Type code: Revision I [dimensions and technical modifications subject to change] Permanent magnetic Non magnetic Nominal width (NW) Length [ 50 mm steps ]Drive arrangement Gear motor Frequ. contr. gear motor Belt quality Lateral guide plates Belt run control Belt speed Operating voltage please specify Standard: 230/400 V - 50 Hz - 3 Ph

Belt Conveyor with gear motor * with rubber coating when flat wire link belt (FDG) and/or v > 60 m/min driving power: defenition over application and dimension: Revision I [dimensions and technical modifications subject to change] Type code: - 0100 - 0150 - nach Tabelle - nach Tabelle -L -R Gear motor Frequ. contr. gear motor - knopped coating - PVC coating - PU-special belt - Keram (high cut resistant) - flat wire link belt (FDG) - special belt type special belt type Belt run control Belt speed Operating voltage Permanent magnetic Non magnetic Nominal width (NW) Length [ 50 mm steps ]...

Belt Conveyor without motor (E=L-150) retractable length slot nuts M8 x 10 * with rubber coating when flat wire link belt (FDG) and/or v > 60 m/min B - shaft on both sides Revision I [dimensions and technical modifications subject to change] Type code: Permanent magnetic Non magnetic Nominal width (NW) Length [ 50 mm steps ]Shaft arrangement Belt quality - knopped coating - PVC coating - PU-special belt - Keram (high cut resistant) - flat wire link belt (FDG) - special belt type Lateral guide plates - without - h = 100 mm - h = 50 mm - h = 30 mm - special design - without - including -...

Belt Conveyor with gear motor below * please specify dimension L1 i * with rubber coating when flat wire link belt (FDG) and/or v > 60 m/min defenition over application and dimension driving power: Revision I [dimensions and technical modifications subject to change] Type code: Permanent magnetic Non magnetic Nominal width (NW) Length [ 50 mm steps ] Drive arrengementGear motor Frequ. contr. gear motor Belt quality - knopped coating - PVC coating - PU-special belt - Keram (high cut resistant) - flat wire link belt (FDG) - special belt type Lateral guide plates - without - h = 100 mm - h =...

Belt Conveyor Equipment Initiator for belt run control by costumerl Initiator for belt run control by costumerl Revision I [dimensions and technical modifications subject to change] Lateral guide plates for NW 250 and wider Lateral guide plates for NW 100 and 200 sliding bend or Magnetic roll

Installation of Equipment acc. to EC Machinery Directive system free accessible Revision I [dimensions and technical modifications subject to change] system fully enclosed system partially enclosed