• Short travel backlit keys• IP65 sealing• Industrial grade50 MM “CHAMELEON” BACKLIT TRACKBALL The “Chameleon" backlit trackballs feature 7-colour illumination of the total ball surface and the mouse button legends. Up to seven different colours can be selected by internal settings on the trackball or by remote dynamic selection via an output connector. For both selection methods, internal or remote, the illumination intensity can be dimmed. The total panel mount unit is sealed to IP65 static and comes with a silicon sponge to seal the carrier plate into the users' cabinet or console. The output is combo PS/2 & USB with autorecognition and in both cases the current for the illumination is drained from the mouse ports. The unit features an aluminium carrier plate with two tactile short travel switches and a dark coloured polyester overlay. • Full backlighting of ball and switches in up to 7 different colours • Colours selectable internally (fixed) or remote (dynamic) • Illumination intensity can be dimmed internally or remotely • Illumination power directly from mouse port, no extra power supply • Proven industrial grade 50mm large trackball • The default backlighting system is powered by the USB port • The backlight intensity and colour can be controlled by using the onboard dipswitches, and is configurable in up to 7 different colours • Compliant to EMC Directive 89/336/EEC for Electromagnetic Compatibility • Low Voltage Directive 73/23/EEC not applicable for our trackballs CONNECTIVITY• The combo PS/2 & USB trackball unit is equiped with a 1,6 meter long shielded straight cable, and connects with a USB type A plug • An adaptor to PS/2 is added. No special device driver is needed, use the standard drivers of your operating system • *Due to the increasing differences of the PS/2 mouse port specifications of the various PC manufacturers, we recommend that this unit should be tested on the final PC configuration and operating system prior to installing it in series The company reserves the right to alter without prior knowledge the specification or design of any standard product or service.

GENERAL TECHNICAL SPECIFICATIONS 50.8mm (2”) Epoxy resin, translucent >= 2 million ball revolutions nom. 50 grams Ball diameter Ball material Lifetime Tracking force Operating temperature range -10°C to +60°C Storage temperature range -25°C to +80°C Unit dimensions Enclosure material / finish Carrier plate Sealing +-600gr 100 x 116 x 40mm Black polyester carrier Aluminium IP 65 static Supply voltage Supply current PS/2 & USB Combo 1 shielded, straight 1.6m long +4.4V +5.25V D.C 28mA (nonbacklit), 50mA (typical), 116mA (white backlit maximum) Key switch actuation force 2.55N Key switch lifetime...

DETAILED ELECTRICAL SPECIFICATION Protocol Table 1: basic electrical specification Table 3: Control connections Notes: 4. if external colour control is required, switches 4,5 and 6 on SW2 must be set to the OFF position. See section 3.1 for details. 5. Colour control connections are not PWM or SSDM compatible. These connections can only be switched up to 50Hz. 6. Colour control lines can be connected to a TTL/CMOS compatible driver, open-collector/open-drain driver or external switches to OV. Pins are pullled to 5V by 5kohm resistor. Colours enabled by a logic low signal. 7. If external intensity...

This connection allows for external LEDs to be attached and controlled by the on-board LED controller. The LEDs must be of common anode type. No resistors are provided for current limmiting on the cathode channels, these must accompany the external LEDs. Description: 4 way, 2mm pitch, right-angled connector Manufacturer: JST (or equivalent) Mating connector: PH, CR or KR types Table 6: Colour control switch function Notes: 11. If external colour control is required; the red, green and blue control switches should be set to the OFF position. Colours can be enabled by applying a TTL7CMOS compatible...

The demo feature allows the trackball to scroll through a sequence of colours by varying the individual LED channels. The feature includes the ability to configure the peak intensity and the scrolling speed, this is configurable only by using the SW2 DIP switch pack. The demo feature is enabled by setting switch 8 on SW2 to the ON position, when enabled the following DIP switch functions apply; Table 8: Scrolling speed configurations for demo feature. The company reserves the riqht to alter without prior knowledqe the specification ordesiqn of any standard product or service.

KEYBOARDS & POINTING DEVICES for the most demanding jobs TCS50F4 (TCL50F1 has the same dimensions and mounting stud) The company reserves the right to alter without prior knowledge the specification or design of any standard product or service.