Catalogs >
Normet Group OY >
Charmec MC 605 DA, short end

Charmec MC 605 DA, short end
8Pages

Catalog excerpts

Technical data sheet 100005925 26.04.2012 Pictured machine may include options and additional equipment. Charmec MC 605 ANFO charger (short end model) with diesel hydraulic drive is designed for face and production charging in underground mines and tunnels up to 65 m2 cross sections where max face height is 8.4 m. ANFO vessels options of 2 x 360 / 500 / 720 litres provides enough explosive storage volume for several faces without need for refuelling. Ready designed place for packed explosives, primers and detonators makes it possible to bring all the needed materials to the workplace at once and eliminates the need for an additional explosive service vehicle. Compressor option eliminates the need for external pressure air line. In production charging optional mechanical hose feeding system allows 33.5 mm or 38 mm charging hoses to be used for up- and down holes. Water adding system allows 1-2 % of water to be added into ANFO during the charging of up-holes for helping ANFO to stay in vertical holes. The liquid cooled turbo charged 110 kW TIER 3 approved engine provides clean and efficient operation and gives maximum speed of 10 km/h in upward 1:7 inclined tunnel. The FOPS /ROPS approved safety canopy / cabin with pivotal instrument console provides comfortable compartment for the driver and his assistant and superior visibility forwards and backwards.The enclosed cabin provides noise level < 75 dB. The Norsmart CAN bus carrier control system comes with fault diagnostics. Self extinguishing marine type wire harness with tinned wires and water tight conduits are specially designed for safe and reliable operation in hard underground conditions. All daily checks can be done from the ground level. Normet reserves the right to change this specification without further notice. Normet Oy Ahmolantie 6 FI-74510 IISALMI, FINLAND

Open the catalog to page 1

Technical data sheet 100005925 26.04.2012 Technical specification CHARGING SYSTEM 2 ANFO vessels and work stand, 1 charging operator 500 liter stainless steel ANFO kettle Pressure max. 7 bar Extra air for charging Pneumatic hand and foot control for charging and blowing Charging hose 19 x 25 mm, 30 m Pneumatic control in basket to switch between vessels Earth straps front and rear Storage area for packaged explosives Storage boxes for primers and detonators Clark 24 000 series power shift with pump drive group 3 speeds forwards and reverse 4-wheel drive AXLES Planetary type Dana 123 Load...

Open the catalog to page 2

Technical data sheet 100005925 26.04.2012 Technical specification 24 VDC ELECTRICAL SYSTEM Exposed components are min IP 65 standard Battery 2 x 115 Ah Alternator 100 A Driving halogen lights (4 + 2 pcs) 70 W Working lights: Halogen lights on cabin (4 pcs) 70 W LED working lights in basket (2 pcs) LED parking, brake and turning indicator lights Side reversing halogen lights (2 pcs) 70 W Rotating beacon, amber Wire harness (self extinguishing) with tinned wires and water tight conduits GREASING SYSTEM Centralized grease fittings for the carrier and boom OTHER 12 kg hand held fire...

Open the catalog to page 3

Technical data sheet 100005925 26.04.2012 Optional equipment Additional equipment CHARGING SYSTEM CHARGING SYSTEM ANFO system: • 2 charging operators (N/A with one ANFO vessel systems) ANFO module: • 1 ANFO vessel and ANFO transport room • 1 ANFO vessel with 4 m3/min onboard compressor ANFO vessel size: • 360 L • 720 L Radio controlled charging and blowing in basket ANFO hose diameter: • For manual hose feeding 22 x 28 / 26,5 x 33,5 / 41,5 x 51 mm Additional pneumatic charging controls: For toe holes and ground level charging work Mechanical ANFO hose feeding for production charging Water...

Open the catalog to page 4

Technical data sheet 100005925 26.04.2012 LTC services SPARE PARTS Spare parts package A: Available for 1000 h of use*. Include periodical service, most common wearing parts and most critical safety parts. Special attention for parts that are crucial for charging process Spare parts package B: Available for 3000 h of use*. Include periodical service, most common wearing parts and most critical safety parts. Special attention for parts that are crucial for charging process * Recommendations are based on average hours - can vary a lot depending on work site conditions TRAINING SERVICES...

Open the catalog to page 5

Technical data sheet 100005925 26.04.2012 SIDE VIEW Basic machine. SIDE VIEW Machine with options and extra equipment. TOP VIEW Machine with options and extra equipment. DIMENSIONS Length Width Height Wheel base Ground clearance as shown Outer Inner WEIGHT Operating Normet reserves the right to change this specification without further notice. Normet Oy Ahmolantie 6 FI-74510 IISALMI, FINLAND

Open the catalog to page 6