Catalog excerpts
cooling system INTRODUCTION NOGA cooling systems were designed to answer various needs for cooling during machining, turning, drilling tapping etc. They are made in three different designs: SIMPLY SOPHISTICATED With MINICOOL, an air + liquid mixture forms a fine spray that cools all metalcutting operations. NOGACOOL consists of a flexible Loc-Line® hose held by a magnet. It is used to easily direct cutting fluid from the coolant pump of machine tools towards the cutting area. The COBRA drop-ejector shoots small quantities of liquid towards a distinct target. Various options enable the user to apply either single drops, or spray burst, or an air stream with small amounts of liquid.
Open the catalog to page 1NOGACOOL NOGACOOL consists of a manifold & Loc-Line® flexible hose with a nozzle on top and a valve at the bottom, assembled on the powerful on/off Popeye magnet. The plug attached can be replaced by a second Loc-Line® hose. NOGACOOL is supplied with a set of three nozzles: 1/16”, 1/8”, 1/4”. Working conditions are as follows: Pressure: 2-3.4 Bar (30-50 Psi) Flow rate: 940 l/hour (250 gal/hour) Max. working Temp. 170°C. Also available with magnet and manifold only (order no. MC0161). Spare parts 324 mm flexible Loc-Line® hose. MC0320 Other dimensions available upon request. 320N Popeye...
Open the catalog to page 2cooling system MINICOOL NOGA MINICOOL is using the VENTURI principle to spray an air + liquid mixture. It consists of the following basic elements: A control valve, spray unit, air line, syphon line and a powerful on/off Popeye magnet, which has a “V” form base, making it possible to mount on non-flat surfaces. The MINICOOL enables the user to easily control both the air flow rate and liquid rate. Stainless steel armoured syphon hose and air hose are made in standard lengths: 1m, 2m, 3m (special lengths available upon request). The spray unit comes in three standard lengths: 264, 334, 479...
Open the catalog to page 3For maximum heat dissipation and extended tool life • Strong magnetic base • Separate on/off air and fluid controls • Stainless steel armoured syphon hose and air hose • Nozzle connected via Loc-Line® flexible hose • Simple, inexpensive, rugged • Single spray unit • Same as MC1700 but with 2 spray units MINICOOL order no.: One spray unit of length (mm) 264 334 479 Two spray units of length (mm) 264 334 479 Syphon hose SIMPLY SOPH
Open the catalog to page 4cooling system OPERATING INSTRUCTIONS The fluid can supplied either by fitting the bowl (CB0146) directly onto the unit, or by using the large container (CB0147) and connecting it to the unit by 4 mm hose. Set up the pneumatic circuit as shown in one of the drawings (a) or (b) or (c). All connections are to be made with 4 mm hose. Open drop size control nut "S" to maximum drop size. Start pulsing the unit by pressing the actuating valve many times, or operate the automatic pulse generator, until drops emerge. Adjust the drop size to your needs. If you have set up the circuit according to...
Open the catalog to page 5COBRA Setup options and accessories Containers Basic COBRA Auxiliary air inlet to break up the drops into spray 4mm dia. Ny hose lon Order no. RNY004 Order no. CB2000 Mechanical Valve Order no. SH1000 110 SIMPLY SOPHISTICATED
Open the catalog to page 6All Noga Engineering catalogs and technical brochures
-
Noga Cooling Systems
20 Pages
-
SP7700
2 Pages
-
YT Range
2 Pages
-
plastic Leaflet
1 Pages
-
deburring system
30 Pages
-
cobra
2 Pages
-
MINICOOL
2 Pages
-
noco
1 Pages
-
NOGA CHIP HOOKS
2 Pages
-
PH holders FAB
2 Pages
-
PH holders FAT
2 Pages
-
Articulated holders FAB
2 Pages
-
Articulated holders FAT
2 Pages
-
New Products 2014
11 Pages
-
THE YT RANGE
2 Pages
-
Blades and Applications
1 Pages
-
Holding Catalog 2
10 Pages
-
Holding Catalog 1
12 Pages
-
Deburring
12 Pages
-
Cooling System
6 Pages
-
Counter brush
2 Pages
-
BASES
2 Pages
-
SPECIALTY BLADES
1 Pages
-
UNIVERSAL HANDY CHUCK HOLDER
3 Pages
-
SETS
5 Pages
-
CONVEXED CERA-CUT
3 Pages
-
NOGA O-RING BURR
2 Pages
-
MINI SCRAPER
4 Pages
-
COUNTERSINK
4 Pages
-
chip hooks
2 Pages
Archived catalogs
-
Specialty blades
1 Pages
-
Ceramic tools
2 Pages
-
Nogacool cooling system
1 Pages
-
Minicool cooling system
2 Pages
-
Cobra cooling system
2 Pages
-
Modular holders
2 Pages
-
Sets & indicators
2 Pages