
Catalog excerpts

Series YB Short Body Pushbuttons Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range i Supplement section. _ Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 50 milliohms maximum for silver; 100 milliohms maximum for gold 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit 100,000 operations minimum Single pole: 1.47N for nonsealed; 1.67N for sealed Double pole: 2.75N for nonsealed; 2.94N for sealed Nonshorting (break-before-make) Pretravel .059" (1.5mm); Overtravel .059" (1.5mm); Total Travel .118" (3.0mm) Materials & Finishes Housing/Bezel: Snap-in Frame: Base: Movable Contactor: Movable Contacts: Stationary Contacts: Switch Terminals: Lamp Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Sealing: Installation Mounting Torque: Quick Connect Force: Soldering Time & Temperature: Standards & Certifications Flammability Standards: UL: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Glass fiber reinforced polyamide (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy with silver plating or brass with gold plating Silver alloy or copper with gold plating Phosphor bronze with tin plating Phosphor bronze with tin plating -25°C through +50°C (-13°F through +122°F) for Illuminated -25°C through +70°C (-13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) IP65 of IEC60529 standard for panel seal models 0.785Nm (6.95 lbfin) maximum 24.5N maximum downward force on connector Manual Soldering: See Profile A in Supplement section. UL94V-0 housing & base File No. E44145 - Recognized only when ordered with marking on switch. Add "/U" or "/CUL" before first dash in part number to order UL recognized switch. All solder lug models recognized at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum. File No. 023535_0_000 - Certified only when ordered with marking on switch. Add "/C" before first dash in part number to order CSA certified switch. All solder lug models certified at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum.
Open the catalog to page 1
Short Body Pushbuttons Series YB Full face or spot illumination with incandescent lamps or multi-element LEDs, with or without resistors. Choice of super bright LEDs in white, green, and blue as well as bright LEDs in red, amber, and green. Combination bezel-barrier is an integral part of the switch and prevents accidental actuation. Unique thermoplastic elastomer seal inside caps plus rolled sleeve of nitrile butadiene rubber at joining of housing and inner case, all for added protection to interior mechanism. Dust and oil tight as well as splashproof panel seal models qualify to IP65 of...
Open the catalog to page 2
TYPICAL SWITCH SPDT DPDT Panel Seal Silver Rated 3A @ 125V AC Gold Rated 0.4VA max. @ 28V AC/DC max. Solder Lug/.110” (2.8mm) Quick Connect Contact Materials & Ratings Bushing Mounting Snap-in Mounting Square Switches are supplied without UL & cULus marking unless specified. UL & cULus recognized only when ordered with marking on switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Touch Green, Super Bright LED Round with Bushing Mounting Black Housing SPDT ON-(ON) Circuit Led Cap with Clear Lens and...
Open the catalog to page 3
Short Body Pushbuttons ORDERING EXAMPLE Incandescent Lamp Solid Cap: Lens/Insert Colors Spot Illuminated Cap: Lens/Insert Colors JA Bicolor LED for Full Face Illuminated Forward Voltage Clear/White Touch
Open the catalog to page 4
Series YB Short Body Pushbuttons POLES & CIRCUITS * When in latchdown position for the alternate circuit, cap position is .020" (0.5mm) above the built-in bezel. PANEL SEAL With Panel Seal Bushing Mounting Supplied with mounting nut. Snap-in Mounting Bushing Mounting only Supplied with mounting nut and o-ring AT089. SHAPES & MOUNTING TYPES Square Bushing Mounting Round Snap-in Mounting Round Bezel-barrier is an integral part of the switch body. HOUSING Black Housing available in black only. The 1-piece body and bezel-barrier have a matte finish. CONTACT MATERIALS & RATINGS Silver Contacts...
Open the catalog to page 5
Short Body Pushbuttons Series YB Solder Lug/ .110" (2.8mm) Quick Connect Epoxy Seak (2.0) .079 _ 03 Straight PC Epoxy Seal (0.6) R_X .024 ^ Single Pole Double Pole INCANDESCENT LAMP & SOLID CAP Electrical specifications are determined at a basic temperature of 25°C. Lamp circuit is independent of switch operation. For dimension drawing of lamp see the Accessories & Hardware section. Solid Cap for Incandescent Lamp & Nonilluminated Lens/Insert Colors Available: White/White Red/White Yellow/White Green/White Blue/White Lens & Insert: Polycarbonate Seal/Filter: Thermoplastic Elastomer...
Open the catalog to page 6
Series YB Short Body Pushbuttons Series YB Short Body Pushbuttons SPOT ILLUMINATED CAP WITH BUILT-IN LED This spot-illuminated cap is factory assembled. AT3011 Round The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Single color LEDs are colored in OFF state. Bicolor LED is translucent white in OFF state. If the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Single Color Single Color Lens/Insert Colors Available:...
Open the catalog to page 7All NKK Switches catalogs and technical brochures
-
A Indicators
2 Pages
-
Series FT
15 Pages
-
KP Series RGB Expansion
8 Pages
-
MS series
4 Pages
-
SCB-Series
3 Pages
-
UB Series
12 Pages
-
WB series
4 Pages
-
YB2
13 Pages
-
Supplement
33 Pages
-
Accessories & Hardware
33 Pages
-
Rotaries
46 Pages
-
Product Overview
6 Pages
-
SmartSwitch
8 Pages
-
Illuminated Pushbuttons
116 Pages
-
Rockers
118 Pages
-
Toggles
119 Pages
-
Pushbuttons
130 Pages
-
Rockers 2013
16 Pages
-
M2 series
7 Pages
-
M series
12 Pages
-
G series
4 Pages
-
D2 series
10 Pages
-
BB series
6 Pages
-
Switches for Tough Environments
12 Pages
-
SMT DIP Rotaries
6 Pages
-
Indicators
31 Pages
-
Touch Screens
17 Pages
-
Tilt Sensors
6 Pages
-
Tactiles
47 Pages
-
Slides
53 Pages
-
Keylocks
23 Pages
-
SmartSwitch
48 Pages
-
Illuminated Pushbuttons
113 Pages
-
Pushbuttons
130 Pages
Archived catalogs
-
Tilt Electrical Ratings
1 Pages
-
SMT Electrical Ratings
1 Pages
-
Keylock Electrical Ratings
1 Pages
-
Rotary Electrical Ratings
1 Pages
-
Tactile Electrical Ratings
1 Pages
-
Slide Electrical Ratings
1 Pages
-
Rocker Electrical Ratings
1 Pages
-
Toggle Electrical Ratings
1 Pages