Catalogs >
NIKKEN KOSAKUSHO >
eMAC DIGITAL BORING HEAD

eMAC DIGITAL BORING HEAD
8Pages

Catalog excerpts

■Fine boring head 　Min. readout : φ0.002㎜/0.0001inch ■Easy digital display ■Wide boring range φ6 - φ110 ■Coolant through : 4Mpa ■Level of protection : IP67

Open the catalog to page 1

f MODULAR TYPE eMAC DIGITAL BORING HEAD MR ■Precision Digital Scale Boring Head Battery Cover ^Counter weight is needed when boring over $92 • Slide travel distance shown on the digital display • Min. readout: 0.002mm / 0.0001inch By direct scale • Wide boring range : $ 6 ~ $ 110 • Coolant through : 4 MPa • Level of protection : IP 67 • Required Battery is SR44 (2 off)

Open the catalog to page 2

MODULAR TYPE eMAC DIGITAL BORING HEAD ■Combination with modular shank Q26 : 　Corresponding to various taper machines φ 54 ~ 110 Digital Boring Head Base Holder for Modular Type Boring Bits Cartridge ・ for eMAC ■Boring Head & EJ Boring Bit ･ ECC Cartridge Layout φ54-86 Boring bit is the minimum layout of the set items Optimal boring bits are also available. Please

Open the catalog to page 3

M BASE HOLDER for MODULAR TYPE (Q26)■Interface of Taper Shank TAPER ★The coupling bolt and wrench are supplied as standard. ★All series have center through (MAX : 4MPa). ★Other shanks are also available. Please contact us for more detail.

Open the catalog to page 4

BASE HOLDER for MODULAR TYPE（Q26） ■Interface of Taper Shank L Coupling Bolt Coupling Bolt Coupling Bolt Coupling Bolt Coupling Bolt Coupling Bolt Coupling Bolt Coupling Bolt

Open the catalog to page 5

Code No. Q26-EMAC6110-61 * Please select boring bit, cartridge and inserts accordingly for the boring head and your cutting conditions. ★Minimum quantity order is 10 pcs / case. ★Please use insert clamp bolt of other manufacturers when using insert of same manufacturers.

Open the catalog to page 6

CPI0IGITHH0E0E] XXX Cutting Edge Thickness Corner Length Radius Cutting Direction Please add the grade indication into O, and add the insert tip material indication at the end off the Code No. e.g. EM09-T4(NX) Tolerance Class G : Ground M : Pressed ■Grade & Material Tip Breaker & Hole Configuration W: T : tS3 R : B : m H : E3 M : fm X : Special ■Reference Cutting Speed ©—Best O—Good — Unsuitable Insert Tip ★Please set the optimum conditions in reference to the above conditions. ★The cutting speed is recommended to be reduced to 50% for interrupted cutting. ★Rapid speed : —6000min-1. Vc:...

Open the catalog to page 7

M MODULAR TYPE eMAC DIGITAL BORING HEAD■eMAC Boring Set Parts List Code. No. ★Base holder for modular type is sold separately. Please refer 11^2 P.3, P.4. ★Please refer 22 P.5 for inserts. •Specifications are subject to change without notice. 5-1, 1-chome, Minamishinden, Daito-shi, Osaka-fu, Japan. Telephone : +81 (0) 72-869-5820 Telefax : +81 (0) 72-869-6220 http://www.nikken-kosakusho.co.jp e-mail:osaka@nikken-kosakusho.co.jp Tel.+1-847-367-4800 MEXICO HERRAMIENTAS LYNDEX-NIKKEN S.A.de C.V. Tel.+44-(0)-1709-366306 F.R.GERMANY NIKKEN DEUTSCHLAND GmbH ITALY VEGA INTERNATIONAL TOOLS S.P.A...

Open the catalog to page 8