UL series
12Pages

Catalog excerpts

TUBE MAKE-TO-ORDER PRODUCTS Coiling Tube for General Pneumatic Piping Coiling Tube Series Tube for General Pneumatic Piping. ● Suitable Stress on Fittings by Coiling Tube. Coiling Tube Twin Coiling Tube Fluororesin / Polyamide Tube Clean Room Tube Anti-Spatter Tube for Flexibility. Nylon for Restoring Force. Anti-Stalic Tube Tube Binder Tube cutter Insert Ring Tube

Open the catalog to page 1

Tube Series ■ Model Designation (Example) UL Coiling Tube Series ③ Tube length (before coiled) ① Tube type 　UL: Polyurethane Coiling Tube 　NL: Nylon Coiling Tube ② Tube dia. (O.D.) Code ※ Tube O.D. ø 3mm is only available for UL (Polyurethane Coiling Tube). 621 Standard Tube Multi-core Tube Nylon Coiling Tube Coiling Tube Polyurethane Coiling Tube ④ Tube color Code Clear blue

Open the catalog to page 2

■ Specifications Tube type Fluid medium Max. operating pressure (at 20℃ 65%RH) Max. vacuum Operating temp. range MAKE-TO-ORDER PRODUCTS ■ Burst Pressure Curve (Reference value) Warning ※ 1. The value of max. operating pressure is measured at 20℃ and 65%RH. When Tubes are used in different conditions, consider a safety ratio of the pressure with an enough margin, referring to Burst Pressure Curve. ※ 2. When Tubes are frequently swung and bent, there is a possibility of generating heat between molecules and damaging the products. Twin Coiling Tube Fluororesin / Polyamide Tube Clean Room Tube...

Open the catalog to page 3

Polyurethane Coiling Tube Standard Tube Multi-core Tube Coiling Tube Nylon Coiling Tube VALVE TUBE Coiling Tube Series Unit：mm Model code UL 03-1- □ UL 03-2- □ UL 03-3- □ UL 03-5- □ UL 04-2- □ UL 04-3- □ UL 04-5- □ UL 04-7- □ UL 04-10- □ UL 04-14- □ UL 04-20- □ UL 06-2- □ UL 06-3- □ UL 06-5- □ UL 06-7- □ UL 06-10- □ UL 06-14- □ UL 06-20- □ UL 08-3- □ UL 08-5- □ UL 08-7- □ UL 08-10- □ UL 08-14- □ UL 08-20- □ UL 10-5- □ UL 10-7- □ UL 10-10- □ UL 10-14- □ UL 10-20- □ UL 12-5- □ UL 12-7- □ UL 12-10- □ UL 12-14- □ UL 12-20- □ Unit：mm Model code ※ . □ in model code : Replaced with Tube color code...

Open the catalog to page 4

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

Open the catalog to page 5

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

Open the catalog to page 6

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

Open the catalog to page 7

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

Open the catalog to page 8

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting...

Open the catalog to page 9

Tube Series Common Safety Instructions for Tubes Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Avoid any load on Tubes such as tensile strength, twisting and bending. These may cause the crush, burst and escape of Tubes. 2. Protect Tubes from scratches caused by snagging or kinking. It may cause the burst of Tubes. 3. The burst pressure of Tubes drops as temperature rises. Read the operating pressure in the catalog well, and apply safety factor. 4. The minimum...

Open the catalog to page 10

Caution 1. When bending tubes, observe the minimum bending radius and minimum installation radius. 2. When piping, provide sufficient lengths of tube, considering possible shrinkage. 3. When Tubes are inserted into Push-In Fitting, make sure that cut end surface of Tubes are right angle, without any scratches on the surface and deformations. 4. Note that the effective cross-section area varies by tube length. Refer to Effective Area of Piping in Tube Performance . ■ Minimum Bending Radius & Minimum Mounting Radius n= Deformation ratio (%). Standard: under 25% d= Tube O.D. L= Measured...

Open the catalog to page 11

UL series 12Pages

Catalog excerpts

All NIHON PISCO CO. catalogs and technical brochures

UL series
12Pages