SSJS series
6Pages

Catalog excerpts

SUS316 Flow Controller - 1 way restricted Flow Controller SUS3 6 SUS31 Newt duc Pro Medical Semi-conductor All parts used are Free from Oil External parts are Food Sanitaion Law compliant （Refer to our website for details） External parts are made of SUS316 stainless steel The material of rubber seal is FKM（HNBR as to diaphragm） Flow controller SUS316 can be distinguished from Needle (Throttle) valve by the marking on the back. Flow controller Marked h e r e Needle valve No marki

Open the catalog to page 1

SUS316 Flow Controller Model designation (Example) Code No entry Specification Normal packaging ⑥. Sealing tape on thread （tapered thread only） Code No entry Specification Standard （※1） ※1） sealing on the thread No ※2） Applying seal tape on the thread (tapered thread). Not for the metric thread type. Seal tape applied Standard ⑤. Grease specification Code Specification No entry -X Oil-free ※1） Fluorochemical grease ※2）（（ ※1） Fluorine coating on rubber seals ※2） Fluorochemical grease is applied on rubber seals ④. Restricted direction Code Control A Meter-out (Exhaust) Restricted flow Free...

Open the catalog to page 2

Flow control valve SUS316 Part Release ring Guide ring Elastic sleeve Fitting Knob Locking nut Main body Needle O-ring C-ring Retainer Diaphragm Core cylinder Lock craws Tubing Materical （Treatment） SUS316 ※1）（ SUS316 FKM （※1） SUS316 SUS316 SUS316 SUS316 ※2）（ SUS316 FKM （※1） SUS316 PBT HNBR Special stainless steel （Austenitic or Ferritic）※3）（ SUS316 Any applicable tubing ※1） Fluorine coating ※2） Metric thread type comes with a gasket （SUS316＋FKM）but there is no sealing tape nor sealock on the tapered pipe thread. ※3） Anti-corrosivity is equivalent to SUS303 Elbow type L2 Tapered pie...

Open the catalog to page 3

SUS316 Flow Controller Flow characteristics SSJSC4-M5④ SSJSC6-M5④ Restricted flow ※） Supply air pressure：0.5MPa, Cylinder speed：at 500mm/sec Turns open Supply air pressure：0.5MPa, Cylinder speed：at 500mm/sec ※） Turns open Turns open Free flow ※） Supply air pressure：0.5MPa, Cylinder speed：at 500mm/sec

Open the catalog to page 4

Flow control valve SUS316 ※） Supply air pressure：0.5MPa, Cylinder speed：at 500mm/sec Turns open Turns open Supply air pressure：0.5MPa, Cylinder speed：at 500mm/sec ※） Free flow Safety instruction Warning 1.When adjusting the speed of actuators, gradually open the air by turning the adjusting needle from a fully closed position. In case the needle is open, an actuator can move suddenly. Turn the needle clockwise to close, and couter-clockwise to open. 2.When adjusting the flow rate, turn the adjusting needle gradually from its fully closed postion. In case the needle is in open position, the...

Open the catalog to page 5

SUS316 Flow Controller Installation 1. How to connect/disconnect a tubing to Push-in Fitting ①.Connecting tubings Insert a tubing into Push-in fitting up to the tube end. Lock-claws bite and hold the tubing spontaneously. The Elastic Sleeve seals the tubing at the same time. Refer to "8-1. Instruction for Tube Insertion" under "Common Safety Instruction for FIttings" in the general catalog of PISCO ②.Tubing disconnection The tubing is disconnected by pushing down the Release-ring to unlock the Lock-claws. Make sure to shut-off the air supply when disconnecting the tubing. ①. Tightening the...

Open the catalog to page 6

SSJS series 6Pages

Catalog excerpts

All NIHON PISCO CO. catalogs and technical brochures

SSJS series
6Pages