Low Abrasion, Low Noise, Full-covered Open-Close Flap Type Model Designation (Example) • Compared with conventional products, improve durability of cables, hoses, and components. • The Full-cover type Plarailchain protect cables and hoses from dust. • Special resins reduce wear and tear of cables and hoses inside by one-fourth to one-fifth of conventional model. • The flap opens on either side and the flap on reverse side opens as well. Calculation of Number of Links K Code Size Free span * Two kinds of brackets, one for fixed-end and the other for moving-end, are required. Select a designation code for the bracket from page 41. The products listed in this page are ECO-friendly products. * Please refer to page 4 for the details of ECO-friendly products. Low Abrasion, Low Noise, Full-covered Open-Close Flap Type Outer periphery In case of ordering, please apply Model code in the following chart. S K 2 * HF in the chart above is the height which Plarailchain is able to pass through using under the length of free span with allowable expansion without load such as cables, hoses, etc. * Please make inquiries for special travel conditions. Inner periphery Number of links is to be calculated by the following equation: S —+a+l 2 n =— P Model code n: Number of links (Figures below decimal point are raised to one positive number) S: Transfer stroke (mm or inch) a: πR + 2K (R: Bending radius (mm or inch), K: Play (mm or inch)) l: Distance from intermediate point (mm or inch) when the fixed-end is not in the middle of transfer stroke ( when the transfer stroke is in the intermediate point : 0) P: Pitch (mm or inch) Setting fixed-end in the intermediate point of transfer stroke minimizes required number of Plarailchain. Detailed Safety Instructions Caution * The metal brackets must be ordered separately. (See P. 41) * Free span is the maximum length that Plarailchain can travel horizontally. Series Max. transfer m stroke Max. transfer speed Plarailchain kg/m weight Plarailchain material Bracket material Nylon 6 (glass 30%) SPCC with chrome plating (RoHS compliance) Service temp. range Operating environment Avoid using in acid/alkaline atmosphere or in hot water * Select bending radius from the above model designation and enter into * Make-to-order production Before using PISCO products, be sure to read "Safety Instructions" and "Common Safety Instructions for Products in This Catalog" on page 13 to 16 and "Common Safety Instructions for Plarailchain" on page 24 to 29.

The products listed in this page are ECO-friendly products. * Please refer to page 4 for the details of ECO-friendly products. Brackets for Attachment of Plarailchain >>> Please refer to the chart on P. 41 Model code Model code Applicable Model code SPO45□ Model code Flap for SPO□ Cover for SPO55□ Flap, Cover Applicable Model code SPO4575 SPO45100 Model code Model code Joint collar Model code SP□Joint collar SPO45125 Model code SP55 Joint collar Model code Flap T for SPO4575 Flap B for SPO4575 Flap T for SPO45100 Flap B for SPO45100 Flap T for SPO45125 Flap B for SPO45125 Flap T for SPO45150...

Common Safety Instructions for Plarailchain Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning : 1. Never step on Plarailchain. Otherwise the chain may break and you will fall down. 2. When connecting, opening, closing, or carrying out maintenance and checks, hold the Plarailchain motionless. Otherwise the Plarailchain may run or fall under its own weight, thus doing injuries to you. 3. Pay attention to the flexing areas of the Plarailchain. You can get injured with your hand...

Capability Diagram When total weight and max. diameter of cable hose, and transfer stroke are decided, please select a best suitable Plarailchain from the following capability diagram. The bending radius of Plarailchain must be larger than the one of cable/hose. Remarks 1. F = Free span = Length can be travelled horizontally 2. The diagram is a case when fixed-end is set to the center of transfer stroke. 3. ø: Maximum diameter of cable or hose to be stored.

Safety Instructions for fixing storage items (tubings/ cables) This instruction is only examples to decrease the wear and tear of tubings/ cables inside the Plarailchain, but do not guarantee the effect for all types. As such, please conduct test use before actual operation. 1. Storage of tubings/cables 1. Please select tubings/cables with less than the minimum-bending radius of plarailchain. In addition, please fix crook of tubings/ cables before installing in Plarailchain. 2. When plenty of tubings/cables are installed, please use "divider" or "rack" inside in order to avoid spiral twist of...

2. Fixing of tubings/cables 1. Please fix tubings/cables as close as possible to the fixing bracket at both ends. Fixing far apart from the bracket causes looseness of the tubings/ cables. 2. Applying metal or resin plates with large surface friction resistance as fixture is acceptable. Tuck tubings/cables between base part and plate as shown below. Note) When a number of tubings/cables are fixed by a banding band together as shown below, some of them might not be touched and fixed by the band and causes loosening. Base part 3. When a number of tubings/cables are fixed by banding band, please...

Safety Instructions for safety device (guide-rail) installation When Plarailchain is used in long stroke or for long time even within the acceptable value of the free-span, the installation of safety device such as guide-rail can prevent sagging or loosening of Plarailchain. (However, the moving speed and acceleration speed are limited by the installation.) Moreover, since the following instruction is only rough indication, please contact PISCO for details. 1. Installation of guide-rail and guide-roller * Do not use guide-roller for the application of more than 1m/s moving speed. Please consider...