Low Abrasion, Low Noise, Open-Close Flap Type Plarailchain SP Calculation of Number of Links Model Designation (Example) SP 1520 In case of ordering, please apply Model code in the following chart. Detailed Safety Instructions * Two kinds of brackets, one for fixed-end and the other for moving-end, are required. Select a designation code for the bracket from page 305. Before using the PISCO device, be sure to read the "Safety Instructions", "Common Safety Instructions for Products Listed in This Manual" on page 13 to 15 and "Common Safety Instructions for Plarailchain" on page 288. (2) Bending radius Size Code Size *1. HF in the chart above is the height which Plarailchain is able to pass through using under the length of free span with allowable expansion without load such as cables, hoses, etc. *2. Please make inquiries for special travel conditions. Code Size (1) Size (Overall dimensions: H × W) Code S (Transfer stroke) Free span • Compared with conventional products, improved durability of cables, hoses, and components.(Special resins reduce wear and tear by one-fourth to one-fifth of conventional products.) • In addition to opening and closing right and left flap remaining as conventional products, the flap inside can be opened and closed. • Rack is available for SP80300 additionally to divider. › Plarailchain material: Nylon 6 + Glass 30% › Bracket material: SPCC + Unichrome plating • Additional sized in the low-wear, low-noise flap open/close type, offering wider variety of choices for users. Number of links is to be calculated by the following equation: S —+a+l 2 n =— P n: Number of links (Figures below decimal point are raised to one positive number) S: Transfer stroke (mm or inch) a: πR + 2K (R: Bending radius (mm or inch), K: Play (mm or inch)) l: Distance from intermediate point (mm or inch) when the fixed-end is not in the middle of transfer stroke (when the transfer stroke is in the intermediate point :

Specifications Model Max. transfer speed lb./ft Plarailchain material Bracket material SPCC with chrome plating (RoHS compliance) Service temp. range Operating environment Avoid using in acid/alkaline atmosphere or in hot water Max. transfer speed lb./ft Plarailchain material Bracket material SPCC with chrome plating (RoHS compliance) Service temp. range Operating environment Avoid using in acid/alkaline atmosphere or in hot water The products listed in this page are ECO-friendly products. * Please refer to page 4 for the details of ECO-friendly products. Metal Brackets for Attachment of Plarailchain...

Low Abrasion, Low Noise, Open-Close Flap Type Low Abrasion, Low Noise, Open-Close Flap Type /ft. mm inch mm inch mm inch mm inch mm inch mm inch m *1. Free span is the maximum length that Plarailchain can travel horizontally. *2. The metal brackets must be ordered separately. (See P.305) *3. Please choose bending radius from the list below and enter into /ft. mm inch mm inch mm inch mm inch mm inch mm inch m *1. Please choose bending radius from the list below and enter into As for SP25**- : R50, R75, R100, R150 As for SP35**- : R100, R125, R150, R175, R200 *4. The raw filled with ■ and with...

Applicable Model Flap Model Flap for SP45125 Flap for SP45150 Flap for SP45175 Joint collar Joint collar Rack divider Rack divider Caution for R-piece and Joint collar Robot Parts * Please choose bending radius (R) from Model Designation in P.304 and enter into

Common Safety Instructions for Plarailchain Be sure to read the following instructions before selecting and using the PISCO devices. Also read the detailed instructions for individual series. Warnings : 1. Never step on Plarailchain. Otherwise the chain may break and you will fall down. 2. When connecting, opening, closing, or carrying out maintenance and checks, hold the Plarailchain motionless. otherwise the Plarailchain may run or fall under its own weight, thus doing injuries to you. 3. Pay attention to the flexing areas of the Plarailchain. You can get injured with your hand caught in the...

Capability Diagram When total weight and max. diameter of cable hose, and transfer stroke are decided, please select a best suitable Plarailchain from the following capability diagram. The bending radius of Plarailchain must be larger than the one of cable/hose. Robot Parts Remarks 1. F = Free span = Length can be travelled horizontally 2. The diagram is a case when fixed-end is set to the center of transfer stroke. 3.

Safety Instructions for fixing storage items (tubings/ cables) This instruction is only examples to decrease the wear and tear of tubings/ cables inside the Plarailchain, but do not guarantee the effect for all types. As such, please conduct test use before actual operation. 1. Storage of tubings/cables 1. Please select tubings/cables with less than the minimum-bending radius of plarailchain. In addition, please fix crook of tubings/ cables before installing in Plarailchain. 2. When plenty of tubings/cables are installed, please use "divider" or "rack" inside in order to avoid spiral twist of...

2. Fixing of tubings/cables 1. Please fix tubings/cables as close as possible to the fixing bracket at both ends. Fixing far apart from the bracket causes looseness of the tubings/ cables. 2. Applying metal or resin plates with large surface friction resistance as fixture is acceptable. Tuck tubings/cables between base part and plate as shown below. Note) When a number of tubings/cables are fixed by a banding band together as shown below, some of them might not be touched and fixed by the band and causes loosening. Base part 3. When a number of tubings/cables are fixed by banding band, please...

Safety Instructions for safety device (guide-rail) installation When Plarailchain is used in long stroke or for long time even within the acceptable value of the free-span, the installation of safety device such as guide-rail can prevent sagging or loosening of Plarailchain. (However, the moving speed and acceleration speed are limited by the installation.) Moreover, since the following instruction is only rough indication, please contact PISCO for details. 1. Installation of guide-rail and guide-roller * Do not use guide-roller for the application of more than 1m/s moving speed. Please consider...