Catalogs >
NIHON PISCO CO., Ltd. >
Small Pressure Sensor 11-series

Small Pressure Sensor 11-series
24Pages

Catalog excerpts

VACUUM ACCESSORIES Sensor Heads, Separate display type Pressure sensor and Vacuum Switch Small Pressure Sensor 11-series Sensor Heads Small-sized pressure sensor head. Width: 10mm, Height: 10mm, Length: 24.5mm “Union” , “Nipple” , and “Male screw” are available. Use of an analog output type and display (SED30-series) has made a separate display system possible. Our small-sized pressure sensors can handle “positive pressure” , “negative pressure” , and “Compound pressure” . Switch output, a total of six different specifications are available. High level of visibility with its the large-sized LED display. All settings can be done using just three push buttons. 11 different types of indication units are available. Small Sensor Two different kinds of output methods are offered- analog output or switch output. Pressure Sensor With Display Various types of installation: in the rear, on a flat surface, panel buried, and protection of display. ● Energy-saving by non-display mode. ● Data saving by Panel Lock. Copper alloy free material and against low ozone concentration on the air flow path. Metal parts material is non-co

Open the catalog to page 1

Vacuum Accessories Series VACUUM ACCESSORIES EXTERNAL VACUUM VACUUM CONTROLLER GENERATOR Small Pressure Sensor 11-series ■ Model Designation of Sensor Heads (Example) VUS ① Small pressure sensor ⑤ Material option ④ Output type ③ Port type and size ① Small pressure sensor Code Sensor ② Display type 11 No display Code Display ③ Port type and size Code Stem Type Push-In-Fitting (mm) 6U 4U ø6 ø4 with holder with holder Code Output AR Compound type / Analog output SR Compound type / NPN open collector ※ . “AR” and “SR” are available with “① VUS” only. Small Vacuum Regulator Add-on Blow-off...

Open the catalog to page 2

■ Specifications of Sensor Heads ■ Switch output Fluid medium Pressure detection Diffusion type semiconductor pressure switch Rated voltage Power consumption Operating pressure range Proof pressure Storage temperature range -20 ~ 70°C (Atmospheric pressure / Humidity: 60% RH or less) 0 ~ 60°C (No freezing) Operating humidity range Protective structure VACUUM ACCESSORIES Operating temp. range Switch output NPN open collector / 30V 80mA or less / Residual voltage: 0.8V or less Operation indicator N.O. (Red LED turns ON, when pressure is above the setting) Switch output Hysteresis Operating...

Open the catalog to page 3

Vacuum Accessories Series VACUUM ACCESSORIES EXTERNAL VACUUM VACUUM CONTROLLER GENERATOR Small Pressure Sensor 11-series ■ Specifications of Display Model code Rated voltage Power consumption 50mA or less (Rated voltage: DC10.8V / 2 switch outputs: ON) Storage temperature range -20 ~ 70°C (Atmospheric pressure / Humidity: 60% RH or less) Operating temp. range Operating humidity range Protective structure Display frequency Response time Variable by digital ﬁlter (About 5, 25, 250 and 2500m･sec) Display accuracy Temperature characteristic Out of display digit range Monitoring system Out of...

Open the catalog to page 4

Pressure sensor Pressure unit Display magniﬁcation (unit) ×1(kPa) Setting code ×102(mmH2O) Display range of ×0.01(bar) rated pressure ×10(mbar) Display of analog output mode VACUUM ACCESSORIES

Open the catalog to page 5

Vacuum Accessories Series ■ Using Method of Sensor Head ■ Switch Output ・Power ON (supply DC power after checking wire arrangement) Pressure adjusting trimmer ・Adjust the pressure adjusting trimmer by the flathead screwdriver (accessory) in order to meet the desired value. ・Apply pressure and check the sensor works correctly. ■ Analog Output (Sensor Head only) ・Power ON (supply DC power after checking wire arrangement) ・Check the output condition with a tester (1-5V). Example of wiring: Switch Output VACUUM ACCESSORIES EXTERNAL VACUUM VACUUM CONTROLLER GENERATOR Small Pressure Sensor...

Open the catalog to page 6

■ Operation Procedure of Display kPa Operation Mode Push both DOWN and MODE buttons for more than a second in Operation Mode. Push both UP and MODE buttons for more than a second in Operation Mode. [Pressure Setting Mode] ①Setting 1 ②Setting 2 ③Hysteresis ④Filter setting VACUUM ACCESSORIES [Initial Setting Mode] ①Display magnification setting (output voltage) ②Switch output setting ③Rated pressure setting Push MODE button for more than a second in Each Setting Mode ■ Zero Point Adjustment of Display kPa Push both UP and DOWN buttons for more than a second in Operation Mode after releasing...

Open the catalog to page 7

Vacuum Accessories Series ■ Initial Setting Mode (Start from the rated pressure setting, when the rated pressure needs to be changed) kPa Push both DOWN and MODE buttons for more than a second in Operation Mode. Small Vacuum Regulator Add-on Blow-off Controller Vacuum Filter Small Sensor ③Three LEDs (-, SW1 and SW2) flash to indicate the setting mode of the display range of rated pressure. Factory setting is 3-digit LED “12P” (0-100kPa). Select the range by pressing DOWN or UP button. VUS11-□A: “-12P” VUS11-□AR: “32r” SEU11-□A: “13P” When “-12P” (0-100kPa) is selected, it flashes to...

Open the catalog to page 8

■ Pressure Setting Mode (Setup rated pressure and SW Output Setting in Initial Setting Mode before this setting) kPa Push both MODE and UP buttons for more than a second in Operation Mode. ④ LED stops flashing.“F--*” will be shown on 3-digit LED which indicates Digital Filter Setting Mode. In the above figure, “F-0” (5msec) is selected. Select a requested filter setting code from 4 types(F-0, 1, 2, 3) by operating DOWN and UP button. You can return to setting① or save all settings and go back to Operating Mode by operating MODE button. Example) Setting Value 1: “-700” is selected. Press...

Open the catalog to page 9

Vacuum Accessories Series VACUUM ACCESSORIES EXTERNAL VACUUM VACUUM CONTROLLER GENERATOR Small Pressure Sensor 11-series ■ Display Magnification and Rated Pressure Setting ■ Display Magnification Setting 　・Set a code of Display Magnification, when LED “-” starts flashing in Initial Setting Mode. 　・Factory setting code is “1” (unit: kPa). ■ Rated Pressure Setting 　・Set a code of Rated Pressure, when LEDs (- / SW1 / SW2) start flashing in Initial Setting Mode. 　・Factory setting code is “12P” (rated pressure range: 0-100kPa). Mode Display Magnification Setting Magnification Code Pressure type...

Open the catalog to page 10

Small Pressure Sensor 11-series 24Pages

Catalog excerpts

All NIHON PISCO CO. catalogs and technical brochures

Small Pressure Sensor 11-series
24Pages