KJNC series
15Pages

Catalog excerpts

CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Flow Control Valve for Sparks Condition Throttle (Needle) Valve ● Control Brass Series Actuator Speed and Pneumatic Signals. ● Adjustable Flow Rate during Air Flow. for High Temp. and Sparks Condition. Rubber Selection for Various Usage in Flame-Retardant and Spatter-Proof by its Brass Made Release-Ring ● Avoid Spatter and Dusts by Protective Cover Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series Silenc

Open the catalog to page 1

Controller Series Throttle (Needle) Valve ■ Model Designation (Example) KJN 01 ④ Seal rubber material Throttle (Needle) Valve Brass Type: C (Elbow) only ③ Protective Cover option ② Thread size Thread size Metric thread (mm) Taper pipe thread ③ Protective Cover option 475 　No code：with cover 　1：without cover Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series with cover ④ Seal rubber material 　No code：

Open the catalog to page 2

■ Specifications Fluid medium Operating temp. range VALVE TUBE Warning ※ .　Make sure to follow the instructions below when the fluid medium is water. 1. Surge pressure must be controlled lower than max. operating pressure when using water as a fluid medium. 2. Be sure to place Insert Ring into the tube edge when using water as a fluid medium. There is a possibility to cause damage to the products, the escape of tube and a fluid leakage without Insert Ring. Operating pressure range ■ Construction (Seal rubber material: HNBR, with cover) Elastic sleeve (HNBR ※ ) Knob (Nickel-plated brass)...

Open the catalog to page 3

Controller Series Throttle (Needle) Valve Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Detailed Safety Instructions 1. When controlling the speed of actuators, slowly release the air by adjusting the needle Manual” on page 23 to 27 and “Common Safety Instructions for Controllers” on page 367 to 368. Warning from a fully closed state. In case the needle is opened, actuator can move suddenly. Turn needle in the clockwise direction to close, and in the counterclockwise to open. 2. Slowly turn the needle to release air from a fully closed state,...

Open the catalog to page 4

■ How to adjust the speed 1. Speed adjustment of actuators ② Reducing speed 　Turn the needle in the clockwise direction direction from a fully closed state. The more moves. Make sure to The speed setting can be changed without tightening the locknut. MAKE-TO-ORDER PRODUCTS ■ How to insert and disconnect 1. How to insert and disconnect tubes ① Tube insertion 　Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and fix it automatically, then the elastic sleeve seals around the tube. 　Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions ②...

Open the catalog to page 5

Controller Series Brass KJNC Elbow Metric thread type Throttle (Needle) Valve Taper pipe thread type Unit：mm Tube O.D. Tube O.D. Model code øD1 øD2 479 Speed Controller Series Stainless Series PP Series ※ “L1” and “L2” are reference values for height dimensions after tightening taper thread. ※ □ in Model code / Replaced with “F” (FKM), or “N” (NBR) for Seal rubber material change Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Chart Characteristic chart p

Open the catalog to page 6

KJNC Elbow without cover Metric thread type Taper pipe thread type Unit：mm Tube O.D. Model code øD 4 MAKE-TO-ORDER PRODUCTS ※ “L1” and “L2” are reference values for height dimensions after tightening taper thread. ※ □ in Model code / Replaced with “F” (FKM), or “N” (NBR) for Seal rubber material change Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series Chart Characteristic chart page

Open the catalog to page 7

Controller Series Brass ■ Flow characteristic Elbow type 481 Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Flow rate (l/min(ANR)) Control flow Control flow Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) Throttle (Needle) Valve

Open the catalog to page 8

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

Open the catalog to page 9

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

Open the catalog to page 10

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

Open the catalog to page 11

KJNC series 15Pages

Catalog excerpts

All NIHON PISCO CO. catalogs and technical brochures

KJNC series
15Pages