CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Pressure Control Valve Pressure Controller Series ● Reduce Primary Pressure from Thread side and Release to Fitting Side. an actuator is operated by a high-pressure, compressed air can be saved by use of the pressure controller to reduce the pressure only during home return. Pressure Control er Series Pressure Gauge Series Check Valve Series Silencer Serie

Controller Series ■ Model Designation (Example) JP Pressure Controller Series Pressure Controller ③ Thread size Thread size Metric thread (mm) Taper pipe thread 519 Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series ■ Specifications Fluid medium Operating pressure range Pressure setting range

■ Construction (Elbow: JPC) Symbol Locknut (Aluminum) Metallic body (Nickel-plated brass) Needle (Nickel-plated brass) Lock-claws (Stainless steel) Release ring (POM) Poppet (Nickel-plated brass) Pressure adjusting spring (Stainless steel) Guide ring (Nickel-plated brass) Elastic sleeve (NBR) Taper pipe thread: Sealock- coating MAKE-TO-ORDER PRODUCTS Metric thread: With gasket (SPCC+NBR) Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” on page 23 to 27 and “Common Safety Instructions for Controllers” on page 367 to...

Controller Series Pressure Controller Series ■ Standard Size List Connection: Thread ⇔ Tube Type JPC Elbow ■ How to adjust pressure 1. Pressure adjustment ① How to increase pressure PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Stainless Series pressure, exhaust direction from a fully Speed Controller Series state, then carry out as ① . Make sure to tighten the locknut at the desired pressure. The

■ How to insert and disconnect 1. How to insert and disconnect tubes CONTROLLER ① Tube insertion 　Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and fix it automatically, then the elastic sleeve seals around the tube. 　Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions ② Tube disconnection 　The tube is disconnected by pushing release-ring to release Lock-claws. 　Make sure to stop air supply before the tube disconnection. MAKE-TO-ORDER PRODUCTS 2. How to tighten thread ① Tightening thread 　Use a spanner to tighten a hexagonal-column....

Controller Series JPC Elbow Tube O.D. Model code øD Pressure Controller Series Metric thread type Hex. Weight CAD (g) file name H ※ . “L1” and “L2” are reference values for height dimensions after tightening taper thread. Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Chart Characteristic chart page

Unit：mm Hex. Weight CAD (g) file name H MAKE-TO-ORDER PRODUCTS Metric thread type Tube O.D. Model code øD ※ . “L1” , “L2” , “L3” and” L4” are reference values for height dimensions after tightening taper thread. Pressure Control er Series Pressure Gauge Series Check Valve Series Chart Characteristic chart page CAD CAD data is available at PISCO

Controller Series ■ Flow characteristic Anti-spatter Series Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series 60 80 100 Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) 120 160 200 Flow rate (l/min(ANR)) Control flow （Primary pressure: 0.7Mpa） 0.7 0.6 0.5 Flow rate (l/min(ANR)) Constant Flow Series Throttle (Needle) Valve Series Control flow （Primary pressure: 0.7Mpa） 0.7 0.6 0.5 Stainless Series Control flow （Primary pressure: 0.7Mpa） 0.7 0.6 0.5 525 Speed Controller Series Control flow （Primary pressure:...

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous conditions....

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper usage...

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors. ③...