Polypropylene + SUS304 Flow Control Valve for Clean Environment Flow Control Valve Copper alloy Non- Clean-room free material grease packaging option (polypropylene) Material for Clean Environment. ● SUS304 ● EPDM Chemical Industry Pharmaceutical for Seal Rubber (Option: FKM or NBR). Very low check valve cracking pressure of In-line straight type 0.725psi (.005MPa) ● Visible Fluid by Translu cent Body Color.

Flow Control Valve PolyPropylene Series ■ Model Designation (Example) PJS Flow Controller PP Series 1/4 ⑧ Packaging option ⑦ Thread sealing option ⑥ Seal rubber material ⑤ Check valve specification In-line Straight ② Tubing dia. Inch size ※. Inch sizes are for In-line type PJSMU type only. Specify 4 for 5 /32" and 8 for 5 /16 " ③ Thread size Thread size Code Size Metric thread(mm) Taper pipe thread  R thread is same as BSPT ④ Control direction Code Control direction ■ Air from thread side is controlled. Air from tube side ■ Air from tube side is controlled. Air from thread is not controlled and...

Union Straight (In-line type) Fluid medium Operating pressure range 7.25psi (0.05MPa) Low cracking pressure type： 2.4psi (0.02MPa) Check valve cracking pressure Operating temp. range Warning ※ 1. The specification above may not be applied, depending on the kind of mixed gases, etc. used as fluid medium. Contact us and make sure to use PISCO products after verifying their suitability on the user side. ※ 2. If operating temp. exceeds 68°F ( 20℃), refer to the following chart “Relation of Operating Temp. & Max. Operating Pressure”. ■ Construction (Union: PJSMU) - IN-LINE type Knob (SUS304) Release...

Flow Control Valve PolyPropylene Series ■ In-Line Connection In-Line Straight symbol mark Unit：mm Model code ※1.Specify "-F" (FKM) or "- HN(HNBR)" in ⑥ o f the model code for a substitute material (FKM comes as the valve packing material even when "-NH" is specified）

Polypropylene Flow Control Valve Flow Controller PJSC Elbow compliant Metric thread type Unit：mm Model code PJSC4-M5 □ (K) ⑥⑦ PJSC4-01 □ (K) ⑥⑦⑧ PJSC6-M5 □ (K) ⑥⑦ PJSC6-01 □ (K) ⑥⑦⑧ PJSC6-02 □ (K) ⑥⑦⑧ PJSC6-03 □⑥⑦⑧ PJSC8-01 □ (K) ⑥⑦⑧ PJSC8-02 □ (K) ⑥⑦⑧ PJSC8-03 □⑥⑦⑧ PJSC8-04 □⑥⑦⑧ PJSC10-02 □ (K)⑥⑦⑧ PJSC10-03 □⑥⑦⑧ PJSC10-04 □⑥⑦⑧ PJSC12-03 □⑥⑦⑧ PJSC12-04 □⑥⑦⑧ ※ 1. “L1” and “L2” are reference values for height dimensions after tightening taper thread. ※ 2. □ in Model code / Replaced with ” A” for Meter-out, “B” for Meter-in ※ 3. ⑥ in Model code / Replaced with “F” (FKM), or “N” (NBR) for Seal rubber...

■ Construction (Elbow (Banjo): PJSC) Symbol Elastic sleeve (EPDM　※ 1) Lock-claws (Stainless steel) Release ring (PP) Tube O-ring (EPDM　※ 1) Resin body (PP) Guide ring (SUS304) ※ 1. FKM / NBR for option ※ 2. Gasket material of metric thread: SUS316+FKM ■ Standard Size List Connection: Tube ⇔ Tube Type PJSMU In-line Straight Connection: Thread ⇔ Tube 10 ● Type PJSC Elbow (Banjo) Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” and “Common Safety Instructions for Controllers”. Warning 1. When controlling the speed of...

■ How to identify the series of Flow Controller Release-ring body color Oval, Round / Black Clean-room package Oval, Round / Light-blue Light-gray Locknut color High-flow Series Round / Black Resin body Low-flow Series Oval, Round / Black SUS303 Series Oval, Round / Dark-blue Round / Semitransparent Semitransparent ※ 1. ( ) is for low cracking pressure type. ■ How to adjust the speed 1. Speed adjustment of actuators ① Increasing speed Turn the needle in the counterclockwise direction from a fully closed state. The more the needle is opened, the faster the actuator moves. Make sure to tighten...

Flow Control Valve PolyPropylene Series ■ Flow characteristic In-line Straight Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Control flow 2500 Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR))

Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) Control flow Free flow Flow rate (l/min(ANR)) Free flow Control flow Free flow Free flow Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR))

Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Control flow Free flow Control flow Free flow Control flow Free flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Control flow Flow rate (l/min(ANR))

Controller Series Common Safety Instructions for Controllers Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Some products have an air direction to control. Make sure to distinguish the direction by marking on the products. Installing the product with the wrong direction may cause personal injury or property damage. 2. Avoid any load on PISCO products such as a tensile strength, twisting, bending, dropping and excessive impacts. These may cause damage to the products....

Caution 1. Refer to “Common Safety Instructions for Fittings” for the safety instructions for fitting part. 2. Instructions for Installing Controllers ① se proper tools to tighten a hexagonal-column or a knurling, when installing U the controller. ② efer to the following table which shows the recommended tightening torque R to tighten thread. Excessive tightening may break the thread part or deform the gasket to cause a fluid leakage. Tightening thread with the tightening torque lower than these limits may cause a loosened thread or a fluid leakage. ● Table: Recommended tightening torque 　(hexagonal-column)...