CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Fixed Orifice Joint Fixed Orifice Joint Series ● Fix ● Lower Price than Throttle (Needle) Valve. ● Installable ● 18 Types of Orifice Bore. Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series Silencer S

Controller Series ■ Model Designation (Example) P Fixed Orifice Joint Series Tube Fitting Thread size: 01 (Taper pipe thread R1/8 only) ③ Orifice bore Code(Orifice bore(mm)) Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Code(Orifice bore(mm))

■ Specifications Fluid medium Operating temp. range VALVE TUBE ■ Construction (Elbow: PL) Lock-claws (stainless steel) MAKE-TO-ORDER PRODUCTS Release ring (POM) Fitting body (PBT) Thread body (Nickel-plated brass) Guide ring (Nickel-plated brass) Elastic sleeve (NBR) Sealock- coating O-ring (NBR) Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series Silencer

Controller Series Fixed Orifice Joint Series FITTING Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Detailed Safety Instructions 1. Before using the product, be sure to check the orifice bore marked on the hexagonal- Manual” on page 23 to 27 and “Common Safety Instructions for Controllers” on page 367 to 368. Caution column. The use of the product with wrong orifice bore will changes the speed of actuator. 2. In case an accuracy of flow rate control is required, select the best Fixed Orifice Joint by actual measurements because the flow rate may vary...

■ How to insert and disconnect 1. How to insert and disconnect tubes CONTROLLER ① Tube insertion 　Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and fix it automatically, then the elastic sleeve seals around the tube. 　Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions ② Tube disconnection 　The tube is disconnected by pushing release-ring to release Lock-claws. 　Make sure to stop air supply before the tube disconnection. MAKE-TO-ORDER PRODUCTS 2. How to tighten thread ① Tightening thread 　Use a spanner to tighten a hexagonal-column....

Fixed Orifice Joint Series Model code ※ . “L” is a reference value for height dimension after tightening thread. Code(Orifice bore) 0.3 øN(mm) Eff. A (mm2) Speed Controller Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Constant Flow Series Anti-spatter Series Anti-spatter Series Stainless Series Stainless Series Throttle (Needle) Valve Series øN Tube O.D. Model code øD PL4-01- □ PL6-01- □ PL8-01- □ ※ . “L” is a reference value for height dimension after tightening thread. Code(Orifice bore) 0.3 øN(mm) Eff. A (mm2) OP. Page for special specifications P.000

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous conditions....

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper usage...

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors. ③...

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a countermeasure,...

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting a...