Hollow Fiber Membrane Type Air Drier Unit electric power supply is required. Air Filter, Mist Filter (Micromist Filter) and Regulator are integrated. type achieving direct connection to air source. Air Filter Mist Filter or Micromist Filter Gauge Option - Bourdon tube Compact Pressure Gauge Battery Operated Digital Display Gauge Dual LCD Display Pressure Sensor Swi

Dry Unit ■ Model Designation (Example) FMDR ① Unit Type ③ Inlet-side Connection Port ④ Outlet-side Connection Port ① Unit Type Code Mist Filter Micromist Filter ② Flow Rate Code Flow Rate(l/min(ANR)) Table 1. Thread Size (Female) 100 Series (*For Rc thread (02 and 03), size of Inlet and Outlet Ports are same.) C6(e.g.)：Fitting Size (Refer to Table 2) ④ Outlet Port (* Selectable for Fitting Size only) No Code：Same size as Inlet port C6(e.g.)：Fitting Size (Refer to Table 2) ⑤ Drainage Cock Table 2. Thread Size of Push-In Fitting C Straight Type MD：Manual Drain Cock AD：Auto Drain Cock No Code：Left...

⑦ Pressure Gauge No entry：Bourdon tube pressure gauge L：No gauge G：Digital pressure gauge T2：Dual LCD digital pressure sensor（1 point SW ＋analog output（2m cable） ） ） T2C：Dual LCD digital pressure sensor（1point SW＋analog output（M8, 4-pin male connector） T3：Dual LCD digital pressure sensor（2 points SW output（2m cable） ） T3C：Dual LCD digital pressure sensor（2 points SW output（M8, 4-pin male connector） ） T4：Dual LCD digital pressure sensor（NPN output, 2 points SW output＋analog output） T4P：Dual LCD digital pressure sensor（PNP output, 2 points SW output＋analog output） T5：Dual LCD digital pressure sensor...

Dry Unit ■ Calculation Method of Dehumidification Amount ● Conditions ［Fig. 2］ (Table of Saturated Vapor Amount) Temp. Vapor Amount Temp. Vapor Amount Dehumification amount is under the following condition. (ºC) (ºC) (g/m3) (g/m3) Compressed air of temp.: 20oC, humidity: 100%, pressure: -50 0.0617 0 4.85 0.7MPa is dehumidified up to dew point -25oC by an air dryer. ■ Example: Calculation Method of Atmospheric Dew Point (Temp.: 20oC, Humidity: 100%, Pressure: 0.7MPa) 　　［Fig. 1］ Atmospheric Dew Point………－ 8℃ Check the saturated vapor at -8oC and -25oC in the figure 1. 　　［Fig. 2］ 　　　　Amount of saturated...

Relative Humidity (%) Air Temp. 25℃ Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” and Common Safety Instructions for Fiber Dry and Dry Unit”. Caution 1. Make sure to adjust the pressure of the regulator in the increasing direction and lock it by pressing the lock button after adjustment. 2. Air is exhauseted from the drain port until the supply pressure rises to 0.05MPa for Manual Drain Type and to 0.15Mpa for Auto Drain Type. During this time, the air will not stop coming out even if the drain knob is turned. (Contact...

Dry Unit ■ How to insert and disconnect 1. How to insert and disconnect tubes ① Tube installation For Dry Unit Series (Dry Unit Series with a Built-in Tube Fitting), insert a Push-In Fitting until it touches to the tube end which makes the lock-claws bite the tube to fix and the elastic sleeve seal around the tube. Refer to “2. Instructions for Tube Installation” under “Common Safety Instructions for Fittings” when installing a tube fitting. ② Tube disconnection The tube is disconnected by pushing the release-ring which releases the lock-claws. Make sure to stop air supply before the tube disconnection....

Unit of Air Filter, Micromist Filter, Fiber Dry and Regulator with Bourdon Tube Pressure Gauge Unit of Air Filter, Mist Filter, Fiber Dry and Regulator with Bourdon Tube Pressure Gauge Purging Flow Adjustment Dial Manual Drain Cock Automatic Drain Cock Push-In Fitting Drainage Drainage Barb Fitting Weight (g) Port Dia.：02(Rc1/4) Port Dia.：03(Rc3/8) 1,593

Dry Unit ■ 100 Series FMDR Unit of Air Filter, Micromist Filter, Fiber Dry and Regulator with Digital Pressure Gauge Unit of Air Filter, Mist Filter, Fiber Dry and Regulator with Digital Pressure Gauge Purging Flow Adjusting knob Digital Pressure Gauge：GPD ø7 Automatic Drain Cock Push-in type Fitting Manual Drain Cock Weight (g) Port Dia.：02(Rc1/4) Port Dia.：03(Rc3/8) 1,602 ※ 1. The dimension of 108.5mm is just for reference. ※ 2. Fill in ③ of model code with 02 for Rc1/4 thread or 03 for Rc3/8 thread. Fill in ⑥ with R only if the flow direction from right to left is needed. Otherwise leave it...

Unit of Air Filter, Micromist Filter, Fiber Dry and Regulator with Digital Pressure Gauge Unit of Air Filter, Mist Filter, Fiber Dry and Regulator with Digital Pressure Gauge Purging Flow Adjusting knob Cable length about 2000 (※2) ： Digital Pressure Sensor Manual Drain Cock Barb Fitting Drainage Drainage For digital pressure sensor： SEU-31-N□ （ model codes come with T2□ and T3□） Push-in type Fitting Automatic Drain Cock For digital pressure sensor：SEU-32-□ （model codes come with T4□ and T5□） ●For model codes with T2 □ and T3 □ Weight (g) Port Dia.：02(Rc1/4) Port Dia.：03(Rc3/8) 1,638 Fill in...

Dry Unit ■ 100 Series FMDR Unit of Air Filter, Micromist Filter, Fiber Dry 100 and Regulator with No Gauge FBDR Unit of Air Filter, Mist Filter, Fiber Dry compliant and Regulator with No Gauge Purging Flow Adjustment Dial Manual Drain Cock Drainage Drainage Automatic Drain Cock Push-In Fitting Barb Fitting Weight (g) Port Dia：02(Rc1/4) Port Dia：03(Rc3/8) 1,556

Micromist Filter and Fiber Dry Mist Filter and Fiber Dry Purging Flow Adjustment Dial Manual Drain Cock Automatic Drain Cock Push-In Fitting Barb Fitting

Dry Unit ■ 100 Series FDR Unit of Air Filter, Fiber Dry and Regulator compliant with Bourdon Tube Pressure Gauge Manual Drain Cock Automatic Drain Cock Push-In Fitting Barb Fitting Purging Flow Adjustment Dial Weight (g) Port Dia.：02(Rc1/4) Port Dia.：03(Rc3/8) 1,246.5

Unit of Air Filter, Fiber Dry and Regulator with Digital Pressure Gauge Purging Flow Adjusting knob Manual Drain Cock Drainage Barb Fitting Automatic Drain Cock Push-in type Fitting Digital Pressure Gauge：GPD Weight (g) Port Dia.：02(Rc1/4) Port Dia.：03(Rc3/8) 1,255 ※ 1. The dimension of 108.5mm is just for reference. ※ 2. Fill in ③ of model code with 02 for Rc1/4 thread or 03 for Rc3/8 thread. Fill in ⑥ with R only if the flow direction from right to left is needed. Otherwise leave it blank (standard flow direc