CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Check Valve Check Valve Series ● One-Side ● Usable Air Flow. Keep Pressure in Outlet Side. in Vacuum Retention State and Low-Pressure Piping. ● Low-cost and Lightweight Resin Type Check Valve Series Silencer Ser

Controller Series ■ Model Designation (Example) CV Check Valve Series Check Valve ③ Tube dia. / Thread size P：Resin type (Only available for CVC and CVU with tube dia. 4/6/8mm and CVF Rc1/8 and Rc1/4) ※ . Material of Bush type body is metal and Poppet is resin. Union Straight Unequal Union Straight ③ Tube dia. / Thread size Tube dia. 533 Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series Taper pipe thread (CVF, CVPF type) ④ Thread size( ※ . In case that ④ indicates tube dia., select tube dia. from table ③...

■ Specifications Fluid medium Cracking pressure Operating temp. range Operating pressure range ■ Construction (Metal type straight: CVC) Release ring (POM) Guide ring (Nickel-plated brass) Elastic sleeve (NBR) Tube end MAKE-TO-ORDER PRODUCTS Lock-claws (Stainless steel) Metallic body (Nickel-plated brass) Spring (Stainless steel) O-ring (NBR) Poppet (Aluminum) Taper pipe thread: Sealock- coating Metric thread: With gasket (SUS304+NBR) ■ Construction (Resin type straight: CVPC) Symbol Tube Release ring (POM) Guide ring (Nickel-plated brass) Resin body (PBT) Lock-claws (Stainless steel) Elastic...

Controller Series Check Valve Series FITTING Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Detailed Safety Instructions 1. Frequent switching may generate heat and cause a danger of getting burnt. Contact us Manual” on page 23 to 27 and “Common Safety Instructions for Controllers” on page 367 to 368. in case of using Check Valve with frequent switching. 1. Make sure to follow “2. Instructions for installing controllers” in “Common Safety Instructions for Controllers”, when tightening thread. Too much tightening may cause a malfunction of poppet. 2....

■ Standard Size List Connection: Thread ⇔ Tube Page Thread size Connection: Tube ⇔ Tube (Equal dia.) Page Connection: Male thread ⇔ Female thread Type CVF Bush CVPF Bush CVU Union Straight P.538 CVPU Union Straight P.538 Type CVPC Straight Connection: Tube ⇔ Tube (Unequal dia.) Page ■ Applicable Tube and Related Products MAKE-TO-ORDER PRODUCTS Tube O.D.1 (mm) 12 CVG Unequal Union Straight P.538 Type Polyurethane Tube………P.596 Nylon Tube………

Controller Series CVC Straight R Tube O.D. Model code øD CVC4-M5 □ CVC4-M6 □ CVC4-01 □ CVC6-01 □ CVC6-02 □ CVC8-01 □ CVC8-02 □ CVC10-03 □ * CVC10-04 □ * CVC12-03 □ * CVC12-04 □ * Metric thread type CAD Effective area Weight (mm2) (g) file name Check Valve Series *Material for metallic body is aluminum. ※ 1. “L” is a reference value for height dimension after tightening taper thread. ※ 2. □ in Model code / Replaced with “A” for Inlet on male thread, “B” for Outlet on male thread Release ring Mini type øD：4、6 Anti-spatter Series Throttle (Needle) Valve Series Constant Flow Series Tube O.D. Model...

Model code ※ .Material for metallic body is aluminum. Release ring Mini type øD：4、6 CVG Unequal Union Straight compliant MAKE-TO-ORDER PRODUCTS CVPU Union Straight (Resin type) Model code ※ . Material of metallic body is aluminum. ※ . □ in Model code / Replaced with “A” for Inlet on ø 12mm, “B” for Outlet on ø 12mm. Air flow direction as below 　　A: ø 12 → ø 10mm 　　B: ø 10 → ø 12mm Check Valve Series OP. Page for special specifications P.000

Controller Series CVF Bush Check Valve Series *Material for metallic body is aluminum. ※ 1. “L” is a reference value for height dimension after tightening taper thread. ※ 2. □ in Model code / Replaced with “A” for Inlet on male thread, “B” for Outlet on male thread 539 Speed Controller Series Stainless Series CVPF Bush (Resin type) PP Series Anti-spatter Series Constant Flow Series Unit：mm Effective area (mm2) Model code Stainless Series ※ 1. “L” is a reference value for height dimension after tightening taper thread. ※ 2. □ in Model code / Replaced with “A” for Inlet on male thread, “B” for...

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous conditions....

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper usage...

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors. ③...