FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Anti-Twisting Coiling Tube for Air Tool Coiling Tube with Twist-Proof Fitting ● Avoid Twisted Tube Problem for Air Tool Built-in at Both Tube End Twist-Proof Fitting Block and Connector Coupling Color Ca

Fitting Series FITTING Coiling Tube with Twist-Proof Fitting ■ Model Designation (Example) ULT Tube color: Yellow only ① Tube length Coiling Tube with Twist-Proof Fitting Tube dia.: Tube O.D. 8mm only Thread size: R1/4 (Male screw), Rc1/4 (Female screw) ① Tube length Code ● Twist-Proof Fitting only 02 Male screw size: R1/4 Tube dia.: Tube O.D. 8mm only 307 Standard Series Mini Series Stainless Series ■ Specifications Fluid medium Max. operating pressure Max. vacuum Operating temp. range Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die Temperature Control Minimal Series Stop...

Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction 1. Since the Twist-proof Fitting is not designed to bear continuous swing and rotation, do not use it for the applications which have such movement continuously. Manual” on page 23 to 27 and “Common Safety Instructions for Fittings” on page 33 to 35. Detailed Safety Instructions VALVE TUBE ■ How to insert and disconnect 1. How to insert and disconnect tubes MAKE-TO-ORDER PRODUCTS ① Tube disconnection 　The tube is disconnected by pushing release-ring to release Lock-claws. 　Make sure to stop air supply before...

Fitting Series FITTING Coiling Tube with Twist-Proof Fitting ULT Coiling Tube with Twist-Proof Fitting Model code PP Series EG Series Anti-spatter ＆ Brass Series Unit：mm Model code PCT Twist-Proof Fitting compliant Chemical Series Stainless Series Mini Series Standard Series R1/4 ※. Reference value for height dimension after tightening thread. Die Temperature Control Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting CAD CAD data is available at PISCO website.

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous conditions....

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper usage...

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors. ③...

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a countermeasure,...

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting a...

Fitting Series Common Safety Instructions for Fittings Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Do not use fittings with fluid medium other than air or water. (Water can be used with some series.) Contact us for using other kind of fluid medium except air and water. 2. o not use fittings except Anti-spatter, Brass and Brass Compression Fitting D series in a place where the flame and weld spatter is produced. There is a risk of causing fire by sparks. 3. As for applications...

　● Table 1. Tube O.D. Tolerance Urethane tube ± 0.05mm ± 0.15mm ± 0.15mm ± 0.15mm ± 0.15mm ± 0.15mm ± 0.15mm ± 0.15mm MAKE-TO-ORDER PRODUCTS 2. Instructions for Tube Insertion ① Make sure that the cut end surface of the tube is at right angle without a scratch on the tube surface and deformations. 1.In case of using non-PISCO brand tubes, make sure the tolerance of the outer tube diameter is within the following limits of Table 1. ② When inserting a tube, the tube needs to be inserted fully into the push-in fitting until the tubing edge touches the tube end of the fitting as shown in the figure...