AP series
18Pages

Catalog excerpts

FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Tube Fitting All PPS Push-In Fitting Type Chemical Series Copper alloy Non- Clean-room free material grease packaging option Chemical Industry Medical Industry Medicine Industry Food Industry made fitting with high heat resistance, flame retardance (UL94 V-0) and chemical resistance. ● FKM for Seal Rubber. 　Option: NBR / EPDM ● Oil-Free for All Parts and Compliant with Japanese Food Sanitation Act. (only FKM option) ● No Worry for Rust and Metal Ion Packaging Option Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die Temperature Control Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting Block and Connector Couplin

Open the catalog to page 1

Fitting Series FITTING Tube Fitting Chemical Series ■ Model Designation (Example) AP All Resin Made (PPS) ﬁtting ⑤ Thread sealing option ④ Seal rubber material Union Straight Union Elbow Unequal Union Stem ③ Thread size ( ※ . In case that ③ indicates tube dia., select tube dia. from table ② ) 169 Thread size Taper pipe thread Code Standard Series Mini Series Stainless Series Chemical Series ④ Seal rubber material 　No code：FKM 　E：EPDM (option) 　N：NBR (option) ⑤ Thread sealing option 　No code：Standard (No Sealock and seal tape) 　TP：Seal tape on thread ⑥ Packaging

Open the catalog to page 2

Fluid medium Air / Water( ※ ) / Other chemicals (※) 0.9MPa Operating temp. range 0 ～ 80℃ (Seal rubber NBR：0 ～ 60℃ ) (No freezing) MAKE-TO-ORDER PRODUCTS Warning ※ . Make sure to follow the instructions below when the fluid medium is water or other chemicals. 1. Surge pressure must be controlled lower than max. operating pressure when using water or liquid as a fluid medium. 2. Be sure to place Insert Ring into the tube edge when using water or liquid as a fluid medium. 3. The specification above may not be applied, depending on the kind of chemicals, solvent, or mixed gases used as fluid...

Open the catalog to page 3

Fitting Series FITTING Tube Fitting Chemical Series Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” on page 23 to 27 and “Common Safety Instructions for Fittings” on page 33 to 35. 1. Check chemical resistance before using the products, when the fluid medium is chemicals, solvent or mixed gases. It may cause damage to the products, the escape of tubes, and a fluid leakage. 2. Do not use this series under the condition with vibration or physical impact. These may cause damage to the products, the escape of tubes...

Open the catalog to page 4

Page Thread size Page Thread size Connection: Tube ⇔ Tube (Equal dia.) APU Union Straight P.174 APV Union Elbow P.175 Connection: Fitting ⇔ Fitting (Unequal dia.) Page MAKE-TO-ORDER PRODUCTS APIG Unequal Union Stem P.177 Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die

Open the catalog to page 5

Fitting Series FITTING Tube Fitting Chemical Series ■ How to insert and disconnect 1. How to insert and disconnect tubes ① Tube insertion 　Insert a tube into Push-In Fitting Chemical Series up to the tube end. Collet fixes the tube automatically. Make sure that it is inserted properly by pulling the tube moderately. 　Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions for Fittings” . ② Tube disconnection 　The tube is disconnected by pushing collet. 　Make sure to stop air supply before the tube disconnection. 2. How to tighten thread ① Tightening thread 　Use a...

Open the catalog to page 6

Effective area Weight CAD (mm2) (g) file name 4.5 ※ 1. “L” is a reference value for height dimension after tightening thread. ※ 2. ④ in Model code / Replaced with “E” (EPDM), or “N” (NBR) for Seal rubber material change (No code: FKM) ※ 3. ⑤ in Model code / Replaced with “TP” for Seal tape ※ 4. ⑥ in Model code / Replaced with “C” for Clean-room package Unit：mm Model code APU4 ④⑥ APU6 ④⑥ APU8 ④⑥ APU10 ④⑥ APU12 ④⑥ MAKE-TO-ORDER PRODUCTS Model code Anti-spatter ＆ Brass Series Minimal Series ※ 1. ④ in Model code / Replaced with “E” (EPDM), or “N” (NBR) for Seal rubber material change (No code:...

Open the catalog to page 7

Fitting Series Chemical Series Tube Fitting R Unit：mm Model code APL4-01 ④⑤⑥ APL6-01 ④⑤⑥ APL6-02 ④⑤⑥ APL6-03 ④⑤⑥ APL8-01 ④⑤⑥ APL8-02 ④⑤⑥ APL8-03 ④⑤⑥ APL10-02 ④⑤⑥ APL10-03 ④⑤⑥ APL12-02 ④⑤⑥ APL12-03 ④⑤⑥ APL12-04 ④⑤⑥ Hex. Effective area Weight CAD (mm2) (g) file name H ※ 1. “L” is a reference value for height dimension after tightening thread. ※ 2. ④ in Model code / Replaced with “E” (EPDM), or “N” (NBR) for Seal rubber material change (No code: FKM) ※ 3. ⑤ in Model code / Replaced with “TP” for Seal tape ※ 4. ⑥ in Model code / Replaced with “C” for Clean-room package Mini Series Chemical...

Open the catalog to page 8

Hex. Effective area Weight CAD (mm2) (g) file name H ※ 1. “L” is a reference value for height dimension after tightening thread. ※ 2. ④ in Model code / Replaced with “E” (EPDM), or “N” (NBR) for Seal rubber material change (No code: FKM) ※ 3. ⑤ in Model code / Replaced with “TP” for Seal tape ※ 4. ⑥ in Model code / Replaced with “C” for Clean-room package MAKE-TO-ORDER PRODUCTS Model code Anti-spatter ＆ Brass Series Unit：mm Effective area Weight CAD (mm2) (g) file name ※ 1. ④ in Model code / Replaced with “E” (EPDM), or “N” (NBR) for Seal rubber material change (No code: FKM) ※ 2. ⑥ in...

Open the catalog to page 9

Fitting Series Chemical Series Tube Fitting Unit：mm Model code APY4 ④⑥ APY6 ④⑥ APY8 ④⑥ APY10 ④⑥ APY12 ④⑥ Effective area Weight CAD (mm2) (g) file name ※ 1. ④ in Model code / Replaced with “E” (EPDM), or “N” (NBR) for Seal rubber material change (No code: FKM) ※ 2. ⑥ in Model code / Replaced with “C” for Clean-room package APIG Unequal Union Stem Standard Series Mini Series Stainless Series Chemical Series Unit：mm Model code APIG6-4 ⑥ APIG8-6 ⑥ APIG10-8 ⑥ APIG12-10 ⑥ ※ . ⑥ in Model code / Replaced with “C” for Clean-room package

Open the catalog to page 10

AP series 18Pages

Catalog excerpts

All NIHON PISCO CO. catalogs and technical brochures

AP series
18Pages