FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Molding Die Temperature Control Coupling Die Temperature Control Fitting Series ● Push-In Fitting Type for Die Temperature Control. Oil, Clean Water and Air for Fluid Medium. Projection left on the die, after uncoupling Plug. Die Temperature Control Valve Built-In Type prevents Hot Water Ejection when uncoupling Plug. Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting Block and Connector Coupling Colo

Fitting Series FITTING Die Temperature Control Fitting Series ■ Model Designation (Example) AK ④ Tube dia. / Inner thread 　AK：Without stop valve (Standard type) 　AS：With stop valve ② Fitting Type（No code: Thread part (socket) only） 　C：Straight 　L：Elbow 　08：08 series (Standard type only) 　10：10 series 245 ④ Tube dia. / Inner thread（No code: Thread part (socket) only） Tube dia. Standard Series Mini Series Stainless Series Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die Temperature Control Inner thread ⑤ Thread size（No code: Fittng part (plug) only） Thread size Taper pipe thread...

Fluid medium Max. vacuum Operating temp. range Water (Clean water ※ ) － Warning ※ . Make sure to follow the instructions below when the fluid medium is water or heat medium oil. 1. Surge pressure must be controlled lower than max. operating pressure when using water or heat medium oil. 2. Be sure to place Insert Ring into the tube edge when using water or heat medium oil. TUBE MAKE-TO-ORDER PRODUCTS ■ Construction (Elbow: AKL) Lock-claws (Stainless steel) Tube End Fitting body (Nickel-plated brass) Release ring (POM) Tube Plug body (Nickel-plated brass) Guide ring (Nickel-plated brass) Collet...

Fitting Series FITTING Die Temperature Control Fitting Series Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” on page 23 to 27 and “Common Safety Instructions for Fittings” on page 33 to 35. 1. Before uncoupling the plug, make sure there is no pressure in the pipe and fluid such as water and heat medium oil are under 30℃ . In case these compressed fluids are still in the pipes and are over 30℃ , there is a possibility that the plug jumps out and cause injury or burns. 2. Do not touch the sleeve when a compressed fluid...

■ Standard Size List Fitting (Plug) + Thread (Socket) Page Thread size Page Thread size AKC-F Female Screw Coms P.253 R1/8 Thread size (Pipe taper thread) Rc1/8 Rc1/4 Rc3/8 ● ● ● ● Tube I.D. (Inch size) 1/4 3/8 Page ネジサイズ AKC-B Straight Barb Coms P.253 R1/8 Fitting (Plug) only Type AKC-P Straight Tube Plug P.254 AKL-P Elbow Tube Plug P.254 AKC-FP Female Screw Plug P.255 Thread size (Pipe taper thread) Rc1/8 Rc1/4 Rc3/8 ● Tube I.D. (Inch size) 1/4 3/8 MAKE-TO-ORDER PRODUCTS AKC-BP Straight Barb Plug P.255 Thread (Socket) only Type Thread size (Pipe taper thread) R1/8 R1/4 R3/8 R1/2 ● Stop Valve...

Fitting Series FITTING Die Temperature Control Fitting Series ■ How to install and uncouple ① Drill a hole on a molding die, based on the thread Heat-proof Sealock size in advance. See “Die Processing Dimension” on page 250. Use a hex key to tighten the thread of socket. Thread （Socket） ② Plug can be coupled with the socket by inserting only. Fitting (Plug) ③ When uncoupling the plug, firstly push the plug until the release-sleeve stops, then pull it out. Since the socket is embedded in the die and there is no convex projection on the die surface, it is convenient to handle the die. Stop Valve...

■ Die Processing Dimension Drill a molding die as the referential dimensions “øP” and “L” in order to embed a socket. Model code AK 08-01S AK 08-02S AK(AS) 10-01S AK(AS) 10-02S AK(AS) 10-03S AK 10-04S Unit：mm longer than øP MAKE-TO-ORDER PRODUCTS ■ Applicable Tube and Related Products Insert Ring………P.668 Tube Fitting Long Type………P.262 Die Temperature Control Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting Block

Fitting Series FITTING Die Temperature Control Fitting Series ■ Plug + Socket AKC Straight Tube Coms B L A øD Unit：mm Tube O.D. Model code øD 251 Standard Series Mini Series ※ “L” is a reference value for height dimension after tightening thread. Stainless Series Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die Temperature Control CAD CAD data is available at PISCO website. Weight Effective area (CV Value) Orifice dia. (mm2) (g)

AKL Elbow Tube Coms Weight Effective area (CV Value) Orifice dia. (mm2) (g) MAKE-TO-ORDER PRODUCTS Tube O.D. Model code øD ※ “L” is a reference value for height dimension after tightening thread. Die Temperature Control Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting Block and Connector Coupling CAD CAD data is available at PISCO websit

Fitting Series ■ Plug + Socket AKC-F Female Screw Coms Die Temperature Control Fitting Series Model code 253 Standard Series Mini Series Effective area (CV Value) Weight Orifice dia. (mm2) (g) AKC-B Straight Barb Coms Chemical Series Anti-spatter ＆ Brass Series ※ “L” is a reference value for height dimension after tightening thread. Stainless Series ※ “L” is a reference value for height dimension after tightening thread. CAD CAD data is available at PISCO website. Effective area (CV Value) Weight Orifice dia. (mm2) (g)

■ Plug AKC-P Straight Tube Plug Recommended socket (thread only) AK08- □ S ※ . □ in Recommended socket model code / Replaced with Thread size MAKE-TO-ORDER PRODUCTS Unit：mm TUBE Model code AKL-P Elbow Tube Plug O-ring øD Tube O.D. Model code øD AKL08-6P AKL08-8P AKL10-8P AKL10-10P AKL10-12P Orifice Recommended socket (thread only) dia. ※ . □ in Recommended socket model code / Replaced with Thread size Die Temperature Control Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting Block and Connector Coupling