Viscosity Cups - Zahn / DIN / AFNOR / FORD / ISO
2Pages

Add to favorites

{{requestButtons}}

Catalog excerpts

Viscosity Cups Your quality control instruments provider Viscosity is a key parameter in the behavior of paints both during the manufacturing process and during application. Proper control of this parameter will result in a better use of the paint. Likewise, knowledge of both the application method and application temperature is required when formulating the paint. Adequate viscosity control at low and high shear rates and assessment of any thiroxotropy are also necessary during mixing in order to avoid later undesirable effects during application. Application Calculation of the viscosity by measuring the time needed to flow through an orifice of specific characteristics (seconds). The Cinematic Viscosity is the relation between the absolute viscosity and the density of a fluid. It is usually called u, consequently u = p/p. Some of the units to express it are m2/s, stoke (St) and centistoke (cSt), with the following equivalences: 1 m2/s = 10000 St = 1x106 cSt. Imagine two different fluids with the same absolute viscosity that flow vertically through an orifice. The fluid with the highest density will flow faster, i.e. the one with the lowest cinematic viscosity. UNE ISO cup (UNE EN ISO 2431) Model ISO 3 ISO 3 con Certificado ISO 4 ISO 4 con Certificado ISO 5 ISO 6 ISO 6 con Certificado Range (cSt) Calibration Oils 7-42 *Note: Traceable Calibration Certificate. / For "ENAC" Calibration Certificate request order code ZPEX034. Unless non-standard cups. FORD cup (ASTM D1200) Model FORD 1 FORD 2 FORD 2 con Calibration Oils C10 NEURTEK S.A. SE RESERVA EL DERECHO DE MODIFICACION SIN PREVIO AVISO. Certificado* FORD 2 con Asa FORD 3 FORD 3 con Certificado* FORD 3 con Asa FORD 4 FORD 4 con Certificado* FORD 4 con Asa FORD 5 FORD 5 con Asa FORD 6 FORD 6 con Asa FORD 8 FORD 8 con Asa *Note: Traceable Calibration Certificate. / For "ENAC" Calibration Certificate request order code ZPEX034. Unless non-standard cups.

Open the catalog to page 1

Viscosity CupsYour quality control instruments provider DIN cup (DIN 53211-85) Accesories Calibration Oils Tripod for cups Cronometer Order Code Order Code Adjustable feet and bubble level Timer / Hour / Alarm Range: 24 hrs. Resolution: 1/100seg

Open the catalog to page 2

All NEURTEK catalogs and technical brochures

1. 

   RHOPOINT INSTRUMENTS NEURTEK

   14 Pages

2. 

   LTL3000 retroreflectometer

   2 Pages

3. 

   RHOPOINT NOVO-GLOSS

   11 Pages

4. 

   MetaVue VS3200

   2 Pages

5. 

   Moisture Meters

   16 Pages

6. 

   NKG Glossmeters

   5 Pages

7. 

   Flow Timer NK1100

   2 Pages

8. 

   Film Applicators

   2 Pages

9. 

   ATX Automatic Applicator

   1 Pages

10. 

    Digital Resistivitimeter RE45

    2 Pages

11. 

    Stainless Steel Pycnometer

    1 Pages

12. 

    Sikkens NK3000 Scratch Tool

    1 Pages

13. 

    Hardness Test Kit

    1 Pages

14. 

    Pencil Hardness Tests

    1 Pages

15. 

    Persoz & König Pendulum Hardness Tester

    1 Pages

16. 

    Cylindrical / Conical Mandrel

    1 Pages

17. 

    Cupping Tester

    1 Pages

18. 

    Hand-Held Enamel Impact Tester

    1 Pages

19. 

    Pull / Push Adhesion, Electronic Adhesion Tester KN-10

    2 Pages

20. 

    Multifunctional Master Paint Plate

    2 Pages

21. 

    Cross Cut tester NK2000

    1 Pages

22. 

    Wet Film Thickness Gauge

    1 Pages

23. 

    Wet Film Thickness Gauge WG

    1 Pages

24. 

    Fineness of Grind Gauges 15,25, 50 and 100 microns Hegman Precision Grindometer

    3 Pages

25. 

    Paint and Coatings

    88 Pages

26. 

    QUALITY CONTROL INSTRUMENTS FOR COATINGS

    6 Pages

27. 

    Impact tester for paint

    2 Pages