ACSDP100H-40 Pulse High-Performance AC Servo Drive 50W–400W ACSDP100H-40 The ACSDP100H-40 is a pulse high-performance AC servo drive supporting 50W–400W motors with singlephase AC220V input. It delivers advanced tuning capabilities and six control modes for demanding precision applications. KEY HIGHLIGHTS Output power range: 50W – 400W Input: Single-phase AC220V -15%~+10%, 50/60Hz High-performance pulse control with advanced auto-tuning 6 control modes: Position, Speed, Torque, Position+Speed, Position+Torque, Speed+Torque mixed Pulse input: Pulse+Direction / CCW-CW / A/B Quadrature / Internal position Electronic gear ratio: Numerator 1–32767 / Denominator 1–32767 RS485 Modbus RTU communication 5-digit LED display with 4-button keypad SPECIFICATIONS PARAMETER Drive Type Pulse High-Performance Output Power Input Voltage Control Mode 0: Position 1: Speed 2: Torque 3: Position+Speed mixed 4: Position+Torque mixed 5: Speed+Torque mixed Protection Functions Overspeed / Main power overvoltage / Undervoltage / Overcurrent / Overload / Encoder fault / Control power fault / Position error Monitor Functions Speed / Current position / Command pulse accumulation / Position error / Motor torque / Motor current / Running status Control Input 1: Servo enable 2: Alarm clear 3: CCW drive inhibit 4: CW drive inhibit 5: Deviation counter clear 6: Command pulse inhibit 7: CCW torque limit 8: CW torque limit Control Output Servo ready / Servo alarm / Position complete / Mechanical brake Regenerative Braking Internal and external resistor support Load Inertia Display / Operation 5-digit LED, 4 buttons (▲ Increment / ▼ Decrement / SET Confirm / ◄ Exit) Position Input Mode 0: Pulse+Direction 1: CCW/CW Pulse 2: A/B Quadrature 3: Interna

Electronic Gear Numerator Electronic Gear Denominator Dimensions (W×H×D) Mounting Depth Control signal input/output connector (DB26 Male) Encoder signal connector (DB15 Female) — connected to motor encoder Communication connectors (RJ45, for RS485 crystal head) Main power input terminals Dynamic braking resistor connection terminals Servo motor output terminals — connect to motor U, V, W phases Protective earth terminal — connect to power supply ground and motor ground Bus capacitor charge indicator. LED on = capacitor charged. Do not touch power terminals while LED is on, even after power-off....

CN2 Pin 7 — Z+ (Input) CN2 Pin 8 — Z- (Input) CN2 Pin 9 — U+ (Input) CN2 Pin 10 — U- (Input) CN2 Pin 11 — V+ (Input) CN2 Pin 12 — V- (Input) CN2 Pin 13 — W+ (Input) CN2 Pin 14 — W- (Input) Encoder Z phase (zero) positive input Encoder Z phase (zero) negative input Encoder U phase positive input Encoder U phase negative input Encoder V phase positive input Encoder V phase negative input Encoder W phase positive input Encoder W phase negative input Encoder frame ground Differential Line Receiver. DI = Digital Input, DO = Digital Output.

WIRING DIAGRAM — POSITION CONTROL MODE Note: P200H supports three-phase 220VAC input Alarm Reset Digital Output Position Command Pulse (5V) Position Command Sign (SV) Chassis Ground 1. The input power suppfy voltage range is 20V-28V DCfand the maximum operating current is 100mA. If using an external 24V power supply, please connect the external power supply +24V to pin 16 (COM), and the external power supply 0V to pin 43 (EOV). 2. The DO output power supply must be provided by the user, with a voltage range of 5V~24V DC. The DO terminal maximum allowable voltage is DC30V, and the maximum allowable...

• Speed Control Mode / Torque Control Mode Wiring DiagramApplicable Models: © P100S-40/P100H-40 © PI00S-75/P1OOH-75 © P200H NEOTON MOTOR | www.neotonmotor.com | [email protected] | Generated October 2, 2026 NEOTON MOTOR | www.neotonmotor.com | [email protected] | Generated October 2, 2026