Boot loader Temp, Comp, POWER MANAGEMENT FEATURES: - Full System in a module: - Add power and an antenna to create a fully functional Wireless Mesh Network node - NeoMesh Protocol Stack optimized for ultra low power and reliability - Generic Application layer which can be configured to suit the product needs - Ultra Small Form factor which allows for easy integration in compact products - Supply Range 2.0 - 3.6V suitable for direct battery operation - RF IO either through U.FL connector or solder pad under module - Wireless Sensor Networks - Automatic Meter Reading - Advanced Metering Infrastructure - Mobile Ad-Hoc Networks - Home Control & Building Automation - Industrial Automation - Alarm and Security Systems - Asset tracking - Agricultural and Forest Monitoring - Extension of NB-IoT/LTE-M networks into hard to reach places

Under no circumstances must the absolute maximum ratings given in Table 1 be violated. Stress exceeding one or more of the limiting values may cause permanent damage to the module. Parameter Table 1: Absolute maximum ratings Caution! ESD sensitive device.Precaution should be used when handling the device in order to prevent permanent damage.2. Conditions for operational use Parameter Table 2: Conditions for normal use. TA = 25°C, VDD = 3.0 V if nothing else stated. Measured on NC2400C module. Please note that average current consumption is given by Protocol Settings. The expected average current...

TA = 25°C, VDD = 3.0 V if nothing else stated. Tab e 5: RF, receive and transmit parameters har- The module is certified for compliance with FCC and CE, and as such spurious emissions and monic levels are below the acceptable limits given by the applicable standards. Page 3 of 14

Table 6: Pin list for module P0-P7: lO's for the Generic Application. Se User Guide for details. Reserved: Pins allocated for future use. Do no connect these. Solder to non connected pad. Pins 29,30,31 only connected on NC1000P-x variants of the module, but also present on NC1000C-8 variants.

. neo.cortec 5. Dimensions and drawing Item 18,00 Figure 2: Module drawing 6. PCB Footprint & Pin numbers A recommended footprint is shown here. Please note that no components must be placed under the module. (18x) All dimensions are nominal and in mm. Figure 3: Module footprint (top-view)

. neo.cortec 7. Product approvals The NC2400 module has been designed to comply with most national requirements for world wide operation. The NC2400 module comes in two versions: NC2400C or NC2400P which are both intended for use in the 2.4GHz frequency band world wide. Modular approval has been uptained for EU, US & Canada. In the following more details can be found related to the individual approvals. 7.1 USA (FCC) Neocortec modules NC2400C and NC2400P have been tested to comply with FCC part 15.247 ”Intentional Radiators”. The devices meet the requirements for modular transmitter approval....

. neo.cortec OEM integration instructions: This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the external antenna(s) that has been originally tested and certified with this module. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any...

. neo.cortec 7.1.2 Validity of using the module certification In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Custom design antennas may be used, however the OEM installer...

. neo.cortec 7.2.1 Host Integration The NC2400C or NC2400P module can be integrated into a finished product without obtaining subsequent ISED Canada approvals for intentional radiators provided that the instructions for integration is followed and that the host device does not contain multiple transmitter modules, however at all times, the integrator must ensure that the module remains compliant with the latest edition of RSS247 while installed in the finished product, including compliance with any possible additional requirements, such as digital device emissions, PC peripheral requirements,...

This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains IC: 11904A-NC2400C1". The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. The NC2400C & NC2400P modules...

Contact NEOCORTEC for detailed recommendations. 9. Moisture sensitivity level The module is a MSL3 device as defined in IPC/JEDEC J-STD-033B.1. 10.1 Part number coding Optional values in parenthesis Custom option code * (3 characters) Firmware build version ** (4 characters) T01 = Tray with 100 modules R05 = Tape/Reel with 500 modules R10 = Tape/Reel with 1000 modules RF Connection: C = U.fl. connector P = PAD under module HW Variant: 2400 = Standard version for band 2.4GHz *) Optional values can not be specified for order quantities below 500 pcs. Orders below 500 pcs will be delivered in trays...

neo.c© rtec11. Package informationAvailable in 100 pcs tray or tape and reel.11.1 Tray dimensions 11.2 Tape & Reel dimensions T ALL DIMENSIONS IN MILLIMETRES UNLESS OTHERWISE STATED. Page 12 of 14 Document version 1.3