POWER MANAGEMENT FEATURES: - Full System in a module: - Add power and an antenna to create a fully functional Wireless Mesh Network node - NeoMesh Protocol Stack optimized for ultra low power and reliability - Generic Application layer which can be configured to suit the product needs - Ultra Small Form factor which allows for easy integration in compact products - Supply Range 2.0 - 3.6V suitable for direct battery operation - RF IO either through U.FL connector or solder pad under module - Wireless Sensor Networks - Automatic Meter Reading - Advanced Metering Infrastructure - Mobile Ad-Hoc Networks - Home Control & Building Automation - Industrial Automation - Alarm and Security Systems - Asset tracking - Agricultural and Forest Monitoring - Extension of NB-IoT/LTE-M networks into hard to reach places

Under no circumstances must the absolute maximum ratings given in Table 1 be violated. Stress exceeding one or more of the limiting values may cause permanent damage to the module. Parameter Table 1: Absolute maximum ratings Caution! ESD sensitive device.Precaution should be used when handling the device in order to prevent permanent damage.2. Conditions for operational use Parameter Table 2: Conditions for normal use. TA = 25°C, VDD = 3.0 V if nothing else stated. Measured on NC1000 module. Please note that average current consumption is given by Protocol Settings. The expected average current...

TA = 25°C, VDD = 3.0 V if nothing else stated. Tab e 5: RF, receive and transmit parameters har- The module is certified for compliance with FCC and CE, and as such spurious emissions and monic levels are below the acceptable limits given by the applicable standards. Page 3 of 13

Table 6: Pin list for module P0-P7: lO's for the Generic Application. Se User Guide for details. Reserved: Pins allocated for future use. Do no connect these. Solder to non connected pad. Pins 29,30,31 only connected on NC1000P-x variants of the module, but also present on NC1000C-8 variants.

. neo.cortec 5. Dimensions and drawing Item 18,00 Figure 2: Module drawing 6. PCB Footprint & Pin numbers A recommended footprint is shown here. Please note that no components must be placed under the module. (18x) All dimensions are nominal and in mm. Figure 3: Module footprint (top-view)

. neo.cortec 7. Product approvals The NC1000 module has been designed to comply with most national requirements for world wide operation. The NC1000 modules comes in two versions: NC1000C-8 or NC1000P-8 which are intended for use in the 868MHz frequency band, and NC1000C-9 or NC1000P-9 which are intended for use in the 915MHz frequency band. 7.1 USA (FCC) The NC1000C-9 or NC1000P-9 using the below mentioned antenna has been tested to comply with FCC part 15.247 ”Intentional Radiators”. The devices meet the requirements for modular transmitter approval. The FCC Grant of Equipment Authorization...

. neo.cortec 7.1.2 FCC Labeling requirements The NC1000C-9 and NC1000P-9 modules have been labeled with their own FCC ID number. Since the number is located on the bottom side and therefor not visible, it is needed to place a label on the outside of the finished product into which the module is installed referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2AB76NC1000C1 -orContains FCC ID: 2AB76NC1000C1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device...

. neo.cortec 7.2 ISED CANADA (IC, Canada, EN) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.” The final end product must be labeled in a visible area with the following: “Contains IC: 11904A-NC1000C1”. The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any...

The NC1000C-8 & NC1000P-8 modules has tested to comply with the following standards: Declaration of conformity with European Union Radio Equipment Directive 2014/53/EU (RED) can be released upon request.

Contact NEOCORTEC for detailed recommendations. 10. Moisture sensitivity level The module is a MSL3 device as defined in IPC/JEDEC J-STD-033B.1. 11.1 Part number coding Optional values in parenthesis Custom option code * (3 characters) Firmware build version ** (4 characters) Packaging: T01 = Tray with 100 modules R05 = Tape/Reel with 500 modules R10 = Tape/Reel with 1000 modules Band variant: 9 = 915MHz ISM Band US/Canada RF Connection: C = U.fl. connector P = PAD under module HW Variant: 1000 = Standard version for band 8 & 9 *) Optional values can not be specified for order quantities below...

neo.c© rtec12. Package informationAvailable in 100 pcs tray or tape and reel.12.1 Tray dimensions 12.2 Tape & Reel dimensions 0.35 ±0.04 ALL DIMENSIONS IN MILLIMETRES UNLESS OTHERWISE STATED. Page 11 of 13 Document version 1.5

For further details on the usage of the module and the NeoMesh protocol stack, please visit www. neocortec.com to download additional documents. Here is a list of relevant documentation: The NC1000 series of modules is also available in other hardware variants which can be well suited for various tasks and applications. Here is a short introduction to the options available: Assemblies for rapid prototyping and short time to market: • Available with all "C" module variants • Compatible with Adafruit Feather series of controller boards • Stand alone breakout board for easy sensor integration •...

. neo.cortec Wireless connectivity made simple.