Catalog excerpts

STRUCTURE AND ADVANTAGES・ ・・・ D-2 TYPES・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D-3 LIFE CALCULATION・ ・・・・・・・・・・・・・・・・・ D-4 RELATION BETWEEN BALL CUIRCUITS AND LOAD RATING・ D-4 MOUNTING・・・・・・・・・・・・・
Open the catalog to page 1
High Speed Clearance Adjustable TOPBALL load plates are designed to "float" in the outer sleeve which allows for clearance between the ball elements and shaft to best suit application requirements. Tolerance interchangeable with Asian Metric Slide Bush Type adjustable type Tolerance interchangeable with Asian Metric Slide Bush Type Figure D-3 Basic Structure of TK Figure D-2 Floating Seal and Self-aligning Feature TOPBALL Unit Figure D -1 Circular Arch Design and G round Surface Raceway Shaft diameter tolerance for TMF and TMA types is the same as Asian Metric slide Bush (refer to...
Open the catalog to page 2
TOPBALL LIFE CALCULATION Since ball elements are used as the rolling element in the NB TOPBALL, the following equation is used to calculate the rated life. If the stroke and number of cycles per unit time are constant, the life time is calculated using the following equation. An appropriate clearance between TOPBALL and shaft is required in TOPBALL operation. Inadequate clearance may cause early failure and/or poor, rough movement. Proper clearance is determined by shaft diameter and housing bore. Table D-4〜6 show recommended tolerances of the shaft and housing bore. L h: life time (hr) ℓs:...
Open the catalog to page 3
TOPBALL USE AND HANDLING PRECAUTIONS Examples of Mounting Rotational motion not supported Figures D-4 to D-9 illustrate mounting methods as example. The NB TOPBALL is designed only for linear motion, so that for applications in which a combination of linear and rotational motion is a requirement, Stroke Bush (P. E-2), Slide Rotary Bush (P. E-8), or Rotary Ball Spline (P. B-30) are recommended. Figure D-4 Use of Holding Plates Figure D-5 Clearance Adjustable Type Figure D-6 Use of Retaining Rings Self Alignment When used with a single bearing on a single shaft or with a single bearing each...
Open the catalog to page 4
TK-OP type - TOPBALL Metric Type - part number structure example TK 20 UU - OP - ST - SK blank: standard SK: anti-corrosion※ self aligning blank: self-aligning ST: non self-aligning* inner contact diameter (dr) seal blank: without seal UU: seals on both sides blank: closed OP: open ※For anti-corrosion the load plates are electroless nickel plated with stainless steel balls. *ST option is available for size 12 to 40 closed type number of ball circuits open type number of ball circuits One-sided seal is also available. Please contact NB for details. * Based on nominal housing bore
Open the catalog to page 5
TW-OP type - TOPBALL Inch Type - part number structure example TW 20 UU - OP - SK blank: standard SK: anti-corrosion※ blank: closed OP: open TW type size seal blank: without seal UU: seals on both sides ※For anti-corrosion the load plates are electroless nickel plated with stainless steel balls. closed type number of ball circuits open type number of ball circuits * Based on nominal housing bore ** Seals are not available on TW3. *** One-sided seal is also available. Please contact NB for details. J inch − − − through .0390 .0590 .0470 .0900 .0900 through basic load rating dynamic...
Open the catalog to page 6
TKA-W TYPE(Euro Standard) - Block Type - - Double-Wide Block Type - part number structure part number structure blank: standard SK: anti-corrosion※ self aligning blank: self-aligning ST: non self-aligning* inner contact diameter seal blank: without seal UU: seals on both sides inner contact diameter blank: standard SK: anti-corrosion※ seal blank: without seal UU: seals on both sides double-wide type ※For anti-corrosion the load plates are electroless nickel plated with stainless steel balls. *ST option is available for size 12 to 40 ※For anti-corrosion the load plates are electroless nickel...
Open the catalog to page 7
TKE-W TYPE(Euro Standard) - Open Block Type - - Double-Wide Open Block Type - part number structure part number structure blank: standard SK: anti-corrosion※ self aligning blank: self-aligning ST: non self-aligning inner contact diameter seal blank: without seal UU: seals on both sides inner contact diameter blank: standard SK: anti-corrosion※ double-wide type ※For anti-corrosion the load plates are electroless nickel plated with stainless steel balls. seal blank: without seal UU: seals on both sides ※For anti-corrosion the load plates are electroless nickel plated with stainless steel...
Open the catalog to page 8
TKD-W TYPE(Euro Standard) part number structure part number structure - Clearance Adjustable Open Block Type - - Clearance Adjustable Double-Wide Open Block Type - blank: standard SK: anti-corrosion※ self aligning blank: self-aligning ST: non self-aligning inner contact diameter seal blank: without seal UU: seals on both sides inner contact diameter blank: standard SK: anti-corrosion※ double-wide type ※For anti-corrosion the load plates are electroless nickel plated with stainless steel balls. seal blank: without seal UU: seals on both sides ※For anti-corrosion the load plates are...
Open the catalog to page 9
Asian Metric Slide Bush Type - Asian Metric Slide Bush Type - - Tolerance interchangeable with - Tolerance interchangeable with basic load rating dynamic static shaft C Co diameter mm N N 1,250 1,550 16 2,090 2,630 20 3,780 4,720 25 major dimensions inner contact diameter outer dimensions mounting dimensions Recommended shaft h E W L F G T B C K S1 f S2 diameter:g6 mm mm mm mm mm mm mm mm mm mm mm mm mm TMA20CUU 20 21 27 54 53 41 35 11 40 40 7 M6 12 5.2 TMA25CUU 25 26 38 76 67 51.5 42 12 54 50 11 M8 18 7 part number basic load rating dynamic static shaft C Co diameter mm N N 2,090 2
Open the catalog to page 10
TWA-W TYPE(Inch Standard) part number structure part number structure - Block Type - - Double-Wide Block Type - blank: standard SK: anti-corrosion※ TWA type seal blank: without seal UU: seals on both sides blank: standard SK: anti-corrosion※ seal blank: without seal UU: seals on both sides double-wide type ※For anti-corrosion the load plates are electroless nickel plated with stainless steel balls. ※For anti-corrosion the load plates are electroless nickel plated with stainless steel balls. * Provided with push-in oil fitting for 1/4" to 1/2" sizes. Sizes from 5/8" to 2" offer a 1/4-28...
Open the catalog to page 11All NB catalogs and technical brochures
-
SLIDE SHAFT SPINDLE SHAFT
24 Pages
-
STROKE BUSH SLIDE ROTARY BUSH
14 Pages
-
SLIDE BUSH
74 Pages
-
SLIDE GUIDE
40 Pages
-
FIT Series
2 Pages
-
Actuator BG15
2 Pages
-
Linear System General Catalog
293 Pages
-
Slide Guide SEBS-BS
4 Pages
-
ROTARY BALL SPLINE SPB type
4 Pages
-
TOPBALL Slide Products
28 Pages
-
Compact Slide Way NYT/NYTS
2 Pages
-
BALL SPLINE SSP-AM type
2 Pages
-
SLIDE SCREW
4 Pages
-
ACTUATOR
39 Pages
-
LINEAR SYSTEM
21 Pages
Archived catalogs
-
General Catalog
289 Pages
-
NB - Slide Way
14 Pages
-
NB - Rotary Ball Spline
2 Pages
-
NB - Actuator
55 Pages
-
NB - Slide Bush
4 Pages
-
NB - Slide Rotary Series
14 Pages
-
NB - Miniature Slide Table
6 Pages
-
NB - Gonio way
8 Pages
-
NB - Slide guide
18 Pages
-
NB - Lienar system
23 Pages