Bipolar Hall sensor AH3013 (Latch Type)

1 / 9 PagesView full catalog

Bipolar Hall sensor AH3013 (Latch Type)

Product catalog summary

Features

Rated working voltage: 4.5 V to 24 V, with a minimum limit of 3.5 V.
Operating temperature range: -55℃ to 150℃.
Rated output current (sink): 25 mA, maximum output current (sink): 50 mA.
Switch response time: approximately 1μs, operating frequency: DC to 100 kHz.
High reliability and safety with no mechanical contact or spark, ensuring stable switch signal.
Compliant with EU RoHS and REACH regulations.

Outline

The AH3013 Hall Sensor outputs a low level when the 'S' pole of a magnet faces the sensor and a high level when the 'N' pole faces it. The output status is latched when the magnet is removed, requiring an opposite polarity magnetic field to change the status.

Block Diagram

The sensor includes a reverse voltage protection, voltage regulators, temperature compensation circuit, Hall-voltage generator, signal amplifier, Schmitt trigger, and open collector output driver circuit. These components ensure stable operation across a wide voltage and temperature range.

Limit Parameters

Storage Temperature: -55 to 175℃.
Supply Voltage: 3.5 to 28 V.
Output Cut-off Voltage: up to 300 mW.
Output Current: up to 50 mA.

Electrostatic Grade

Electrostatic compression exceeds ±6kV under human mode.

Operating Conditions

Supply Voltage: 4.5 to 24 V.
Operating Temperature: -55 to 150℃.
Output Current: up to 8 mA.

Electrical Characteristics

Output Low Level: 0.2 to 0.4 V.
Output High Level: 23.5 to 24 V.
Output Leakage Current: 0.1 to 10 μA.
Supply Current: 3.5 to 8 mA.
Output Rise Edge Time: 125 to 150 μs.
Output Fall Edge Time: 60 to 80 μs.

Magnetic Characteristics

Operate Point (BOP): 4 to 7 mT.
Release Point (BRP): -7 to -4 mT.
Hysteresis: 4 to 14 mT.

Package Outline

Available in SOT23-3L, SOT-89, and TO-92UA/TO-92S packages. Pin configuration: Pin1 is Vcc, Pin2 is GND, Pin3 is the output terminal.

Catalog excerpts

Bipolar Hall sensor AH3013 (Latch Type)-1

Latch Type Hall Sensor AH3013

Open the catalog to page 1

Bipolar Hall sensor AH3013 (Latch Type)-2

Latch Type Hall Sensor AH3013 ◆ Features  Rated working voltage 4.5 V ~ 24 V, the limit voltages as low as 3.5 V;  Operating temperature range: -55℃ ~ 150℃;  Rated output current(sink) : 25 mA, the maximum output current(sink): 50 mA  Switch response time is about 1μs, the operating frequency DC ~ 100 kHz;  Small temperature drift between operating point and release point;  No mechanical contact, no spark, switch signal stability, no shaking moment, high reliability and safety;  Products meet the EU RoHS instruction 2011/65 / EU and REACH regulations 1907/2006 / EU requirements 南京艾驰电子科技有限公司...

Open the catalog to page 2

Bipolar Hall sensor AH3013 (Latch Type)-3

Latch Type Hall Sensor AH3013 ◆ Outline When the ―S‖ pole of magnet faces the mark surface of the sensor and is closed to sensor （B≥Bop），the sensor outputs low level; When the ―N‖ pole faces the mark surface and is closed to sensor （B≤Brp） the sensor outputs high level. When the magnet is far away from ， the sensor (B=0), the output status of the sensor is latched and keeps constant. In order to change the output status, the applied magnetic field must be opposite polarity. The magnet and electric transfer characteristic curve of AH3013 is shown as the figure: 南京艾驰电子科技有限公司 NANJING AH ELECTRONIC...

Open the catalog to page 3

Bipolar Hall sensor AH3013 (Latch Type)-4

Latch Type Hall Sensor AH3013 ◆Block Diagram Hall sensor AH3013 is one of bipolar excitation single-ended digital output Hall IC. The output signal owns latch function. The sensor chip has built-in reverse voltage protection, voltage regulators, temperature compensation circuit, Hall-voltage generator, signal amplifier, Schmitt trigger and open collector output driver circuit unit etc. Excellent voltage regulator and temperature compensation circuit ensure the sensor stable operates over a wide voltage range and temperature range, and the reverse voltage protection circuit avoids the sensor to...

Open the catalog to page 4

Bipolar Hall sensor AH3013 (Latch Type)-5

Latch Type Hall Sensor AH3013 Pm-iw Parameter Symbol Min. Max. Unit Storage Temp. Supply Voltage Output Cut-off Voltage Under human being mode, the Electrostatic compression is large than ±6kV. 513 NANJING AH ELECTRONIC SCIENCE & TECHNOLOGY CO.,LTD ADD : 33 B 202-2 S Room 202-2, Bldg B, 33, Dongqi Road, Nanjing, 211103 TEL : 86-25-84609021 FAX : 86-25-84670370 E-mail : [email protected] Web: www.ahest.com

Open the catalog to page 5

Bipolar Hall sensor AH3013 (Latch Type)-6

Latch Type Hall Sensor AH3013 Pm-iw ♦Operating Condition Parameter Symbol Min. Max. Unit Test Condition Parameter Symbol VCci=4.5 , Vcc2=24V , Output High Level VOH 23.5 24 V Output Leakage Current OH Output Rise Edge Time Output Fall Edge Time 613 NANJING AH ELECTRONIC SCIENCE & TECHNOLOGY CO.,LTD ADD : 33 B 202-2 S Room 202-2, Bldg B, 33, Dongqi Road, Nanjing, 211103 TEL : 86-25-84609021 FAX : 86-25-84670370 E-mail : [email protected] Web: www.ahest.com

Open the catalog to page 6

Bipolar Hall sensor AH3013 (Latch Type)-7

Latch Type Hall Sensor AH3013 Test Condition : VCCi = VCC2 =24V , IO = 50mA Hysteresis I Operate point -Release Point I Note 1: Unit is mt, 1mt=10Gs Note 2: When the “S”Pole of the magnetic field is vertical to the front mark of product, we call the magnetic field B > 0. H9 NANJING AH ELECTRONIC SCIENCE & TECHNOLOGY CO.,LTD ADD : 33 B 202-2 S Room 202-2, Bldg B, 33, Dongqi Road, Nanjing, 211103 TEL : 86-25-84609021 FAX : 86-25-84670370 E-mail : [email protected] Web: www.ahest.com

Open the catalog to page 7

Bipolar Hall sensor AH3013 (Latch Type)-8

Latch Type Hall Sensor AH3013 南京艾驰电子科技有限公司 NANJING AH ELECTRONIC SCIENCE ＆ TECHNOLOGY CO.,LTD ADD：南京市江宁区东麒路 33 号国际研发园 B 幢 202-2 室 Room 202-2, Bldg B, 33, Dongqi Road, Nanjing, 211103 TEL：86-

Open the catalog to page 8

Bipolar Hall sensor AH3013 (Latch Type)-9

Latch Type Hall Sensor AH3013 Note: In the package outline, Pin1 is Vcc, Pin 2: GND, Pin3: output terminal。  Mark Mark ―XX‖or ―AHXX‖ are abbreviation form of parts No.  Pin Identify M Type: It faces product mark, and two pins are downward, towards the left, clockwise, the pin No. is 1、2、3 in turn. 南京艾驰电子科技有限公司 NANJING AH ELECTRONIC SCIENCE ＆ TECHNOLOGY CO.,LTD ADD：南京市江宁区东麒路 33 号国际研发园 B 幢 202-2 室 Room 202-2, Bldg B, 33, Dongqi Road, Nanjing, 211103

Open the catalog to page 9