Catalogs >
NACHI America >
GSX MILL Series

GSX MILL Series
16Pages

Catalog excerpts

高い抗折力と耐熱衝撃性に優れた微粒超硬合金の採用により生材のウッェト加工での信頼性を向上耐摩耗性、耐熱性を高めた新GSXコートの採用により幅広い被削材での長寿命化と信頼性を向上 Excellent deﬂecting strength and thermal shock resistance to adopt micro grain carbide. It improves reliability in wet milling of soft materials. Excellent heat resistance and wear resistance to adopt new GSX coat. It is long tool life in a wide milling area. 高硬度材を高速切削 High speed milling hardened materials 切削条件 Milling Condition 切削速度： 300m/min Cutting Speed 炭素鋼のウェット溝加工新GSXコーＡ -Ｃ -Ti系複合多層膜トはｌｒ耐熱性と耐摩耗性を向上で高硬度材の高速ドライ加工に対応切りず離れにも優れるく The new GSX is a multi-layered Al-Cr-Ti alloy...

Open the catalog to page 2

ゼネラルでスペシャルなスーパー汎用エンドミルです。豊富なラインナップでベストチョイスしてください。極ショート刃で抜群の加工面精度 Super accurate surface milling with extremely short cutting edge GSX4C-1Dは底面仕上げ加工に抜群の加工面精度高速高能率の仕上げ加工に最適 Milling Condition 切削速度： 150m/min Cutting Speed 8000min-1 送り速度： 840mm/min GSX4C-1D has extremely accurate milling to finish bottom surfaces. Perfect for high-speed high-performance finishing work. 切り込み　 : p=0.05mm Depth of Cut e=3mm 被削材： S50C Work Material Cutting Fluid　Water soluble ギャッシュランドで抜群の耐チッピング性 Gash land provides superior chipping resistance GSX MILLはギャシュランッド溝でウッェト加工でも耐チッピング性を発揮コーナが欠けにく、く形状を長く確保...

Open the catalog to page 3

シリーズ構成表 Configuration table 刃数 Four Flutes Cutting edge length Three Flutes 被削材選定基準 Selection Chart 被削材 Work Material 構造用鋼 Structural Steels Carbon Steels Alloy Steels プレ調質鋼ハードン鋼ダイス鋼 Pre-hardened Steels Hardened Steels Hardened Steels

Open the catalog to page 4

1. Adjust milling condition when an unusual vibration, different sound occur bv cutting 2. When using low speed machines, use the maximum speed and adjust the feed rate 3. Use highly rigid machining center and holder 5. Use in wet condition in case of Stainless Steels, Nickel Alloys, Titanium Alloys 6. When chattering occurs, reduce the rotation and feed rate, or reduce the depth of cut Recommend dry milling (air blow). However, use the water-miscible cutting fluid for stainless steels High-Speed Milling condition doesn't contain the Nickel Al

Open the catalog to page 5

Stf^—vT<75>ilR(^£'fcfS'£K/£c^o Please read the notice which is the previous page.

Open the catalog to page 6

Helix angle Work Material Nickel Alloys, Titanium 1. Use highly rigid machining center and holder 3. Use in wet condition in case of Stainless Steels, Nickel Alloys, Titanium Alloys 4. When chattering occurs, reduce the rotation and feed rate, or reduce the depth of cut 5. Recommend dry milling (air blow) for high speed milling. However, use the water-miscible cutting fluid for stainless steels

Open the catalog to page 8

Open the catalog to page 9

Open the catalog to page 11

1. Use highly rigid machining center and holder. 3. Use in wet condition in case of Stainless Steels, Nickel Alloys, Titanium Alloys. 4. When chattering occurs, reduce the rotation and feed rate, or reduce the depth of cut. 5. Recommend dry milling (air blow) for high speed milling. However, use the water-miscible cutting fluid for stainless steels.

Open the catalog to page 12

1. SSbtilll^f^taCtt^HlttroSSfflJSrorl^ffiM-A^^-S-C'ffiffl^fSlV 1. Use highly rigid machining center and holder 3 X?>UXiS, S^-^ASim-f 3i#-&ftr>i'7ST-imUT<f.:*3l.,o 3- Use in wet condition in case ot Stainless Steels, Nickel Alloys, Titanium Alloys. 4 Xx>UXS ?-?>&:&roKlJlJ>-?"l[]IT'(tO 1 DT'roXx'77'lIllS-if -=T<f*Sl-,o 4- Use steD,eed in drilling tor Stainless Steels, Nickel Alloys, Titanium Alloys. The amount ot the step is 0.1 D

Open the catalog to page 13

SPttDiJ^lft Standard Milling Condition GSX MILL 4$£3) 4D GSX MILL Four Flutes 4D 1. Adjust milling condition when an unusual vibration, different sound occur by cutting 2. When using low speed machines, use the maximum speed and adjust the feed rate 3. Use highly rigid machining center and holder 5. Use in wet condition in case of Stainless Steels, Nickel Alloys, Titanium Alloys 6. When chattering occurs, reduce the rotation and feed rate, or reduce the depth of cut

Open the catalog to page 14

SP^iJ^ft Standard Milling Condition GSX MILL 2$£?D 4D GSX MILL TWO Flutes 4D 1. Adjust milling condition when an unusual vibration, different sound occur by cutting 2. When using low speed machines, use the maximum speed and adjust the feed rate 3. Use highly rigid machining center and holder 5. Use in wet condition in case of Stainless Steels, Nickel Alloys, Titanium Alloys 6. When chattering occurs, reduce the rotation and feed rate, or reduce the depth of cut

Open the catalog to page 15

Realize incredible high efficiency milling Suitable for high precision finishing of hardened molding dies GS MILL Roughing / Roughing Radius GS MILL Hard Ball Realize stable milling by wave type nicks It reduces cut resistance and raises strength by optimization of nicks pitch. Long tool life in a smoothing coat Smoothing coat and micro grain carbide improve wear resistance. Ultra micro grain carbide with low Cobalt content suppresses micro plastic deformation during milling and increase tool life. High accuracy ball nose +3--7/jm Realize high accuracy ball nose by "One-Pass" grinding...

Open the catalog to page 16

GSX MILL Series 16Pages

Catalog excerpts

All NACHI America catalogs and technical brochures

GSX MILL Series
16Pages