Cable drag chain systems MP 30.1/.2, MP 30.3/.4

• BROAD INTERIOR LAYOUT • BRUSH SUPPORT • CHAIN BRACKET WITH INTEGRATED STRAIN RELIEF TECHNICAL DATA Loading side Inside or outside bend Available interior widths With plastic frame bridge 40.0 – 200.0 mm 2 © Murrplastik Systemtechnik GmbH • MP_30_1__2_MP_30_3__4_~20171211~890280~efk

TECHNICAL SPECIFICATIONS murrplastik Travel distance gliding Lg max. Contact our engineering department to meet any higher requirements: [email protected] MATERIAL PROPERTIES Standard material Other material properties on request. GUIDE CHANNELS STRAIN RELIEF CHAIN BRACKET H-shaped shelf unit RE 3 © Murrplastik Systemtechnik GmbH • MP_30_1__2_MP_30_3__4_~20171211~890280~efk_typ_30_1_2_3_4

MP 30.1/.2 OPEN / MP 30.3/.4 CLOSEDORDERING KEY Dimensions in mm [US inch] ORDER SAMPLE: 0030 01 040 060 0 0 1250 Frame bridge in outside bend, frame bridge in inside bend, can be opened from outside bend Inside width 40 mm; radius 60 mm Plastic bridge, full-ridged with bias, material black-coloured polyamide Chain length 1250 mm (25 links) © Murrplastik Systemtechnik GmbH • MP_30_1_2_MP_30_3_4_~20171211~890280~efk_typ_30_1_2_3_4

SELF-SUPPORTING LENGTH The self-supporting length is the distance between the chain bracket on the moving end and the start of the chain arch. The installation variant FLg offers the lowest load and wear for the energy chain. The maximum travel parameters (speed and acceleration) can be applied for this variant. HS = Installation height plus safety HMA = Height of moving end connection FLg = Self-supporting length, upper run straight FLb = Self-supporting length, upper run bent LOAD DIAGRAM FOR SELF-SUPPORTING APPLICATIONS FLg Self-supporting length, upper run straight In the FLg range, the chain...

murrplastik EINBAUMASSE The moving end chain connection is to be screw fixed at height Hma for the respective radius. Concerning the installed dimensions, you must take into account whether the chain links are equipped with or without bias. For chain links without bias, the “Installed height without bias Hsk” value has to be taken into account. If the chain links are equipped with a bias, the value “Installed height with bias Hsv” has to be taken into account. © Murrplastik Systemtechnik GmbH • MP_30_1 2_MP_30_3_4_~20171211~890280~efk_typ_30_1_2_3_4

MP 30.1/.2 OPEN / MP 30.3/.4 CLOSEDKA 30 FLEXIBLE CHAIN BRACKET This chain bracket offers universal connection options (top, bottom and front) and is attached to the ends of the chain like a side link. This allows the chain to move right up to the bracket. Each chain requires one male and one female bracket. M5 screws and insert panels are used to secure the brackets in place. By default, the chain bracket is supplied with frame bridges. The chain connection can then be optionally fitted with frame bridge strain relief RS-ZL or with strain relief using C-rails and bow clamps type STF. Configurator...

MP 30.1/.2 OPEN / MP 30.3/.4 CLOSEDSEPARATOR / SHELVING SYSTEM MP 30 We recommend that separators be used if multiple round cables or conduits with differing diameters are to be installed. © Murrplastik Systemtechnik GmbH • MP_30_1_2_MP_30_3_4_~20171211~890280~efk_typ_30_1_2_3_4

murrplastik RB-3 SHELF Type 9 © Murrplastik Systemtechnik GmbH • MP_30_1_2_MP_30_3_4_~20171211~890280~efkJyp_30_1_2_3_4

murrplastik RB-3 SHELF Type The shelf RBD creates a horizontal separation over the entire width of the chain link. When used together with the TRT 30 separator, an additional, vertical division can be realised. Type One-piece shelving system, the shelf cannot be varied in height. Type © Murrplastik Systemtechnik GmbH • MP_30_1_2_MP_30_3_4_~20171211~890280~efk_typ_30_1_2_3_4

MP 30.1/.2 OPEN / MP 30.3/.4 CLOSEDMP 30 BRUSH SUPPORT The cables in the neutral strand are routed through the brush supports. This innovative solution was developed especially for applications where cables are subjected to higher levels of wear from cyclical movement. RS-ZL-3 FRAME RAIL TENSION RELIEF Fixed integrated frame bridge strain relief plates in the chain brackets. Tailored to all frame bridge widths up to 200 mm. May be assembled on the inside and outside bends at both chain endings. MP 30.1/.2 OPEN / MP 30.3/.4 CLOSED Type © Murrplastik Systemtechnik GmbH • MP_30_1 _2_MP_30_3__4_~20171211~890280~efk_typ_30_1_2_3_4...

murrplastik STRAIN RELIEF WITH STEEL FIX C-rails (galvanized) for permanent integration, for accommodating the Steel Fix bow clamps in the chain brackets. The bow clamps can take up to 3 cables and are suitable for C-rails with a groove width of 11 mm. Due to the design of the trough elements, a cable preserving cable guidance is ensured. May be assembled on the inside and outside bends at both chain endings. The overall height stated is a guide only. The actual height is, amongst other things, dependent on the diameter and the quality of the cable. A safety distance of 10 mm at the fixed point above...

MP 30.1/.2 OPEN / MP 30.3/.4 CLOSEDLOWERED FIXING POINT MP 30 It is sometimes necessary to lower the height of the moving attachment point. In such cases, modifications to the chain layout should be noted (e.g. extension of chain). Please contact our application engineers. MP 30.1/.2 OPEN / MP 30.3/.4 CLOSED © Murrplastik Systemtechnik GmbH • MP_30_1 _2_MP_30_3__4_~20171211~890280~efk_typ_30_1_2_3_4

MP 30.1/.2 OPEN / MP 30.3/.4 CLOSED GUIDE CHANNEL VAW (ALUMINIUM / STAINLESS STEEL) A range of variable guide channel systems, constructed from aluminium or stainless steel sections, are available for this energy chain. The variable guide channel ensures that the energy chain is supported and guided securely. For help on choosing, please consult the chapter “Variable Guide Channel System”. 14 © Murrplastik Systemtechnik GmbH • MP_30_1_2_MP_30_3_4_~20171211~890280~efk_typ_30_1_2_3_4

ASSEMBLY GUIDE CHANNEL VAW (ALUMINIUM / STAINLESS STEEL) All details given in our sales material prospectuses and catalogues as well as the information available online are based on our current knowledge of the products described. The electronic data and files made available by Murrplastik, particularly CAD files are based on our current knowledge of the product described. A legally binding assurance of certain properties or the suitability for a certain purpose can not be determined from this information. All information with respect to the chemical and physical properties of Murrplastik products...