Catalog excerpts
Cable entry and cable holding systems Cable entry and Cable holding systems 11
Open the catalog to page 1Cable entry plates for pre-assembled cables The cable entry panel system is a split system that solves problems like introducing pre-assembled cables into enclosures, for example. Page 10 Cable entry plates for cables without plugs Accessories A real alternative to cable fittings. With this system cables made of plastic, aluminium or stainless steel can be installed in a flash. Page 58 Accessories for cable entry systems/panels KDL/KDP Under accessories you will find various blanking plates, floor sheeting, adapter plates for cut-out reduction and discharge plates for EMC applications. Page...
Open the catalog to page 3Contents Introduction Catalogue overview Contents Introduction Cable entry and cable holding systems Cable entry plates for pre-assembled cables 3 4–7 8–9 10–56 System overview 10–11 KDL / E cable entry system 13–22 – Advantages – Overview – Selection table (possible combinations of cable entry systems and grommets) – Material data for the entire system (cable entry systems with grommets) – Cable entry system, type KDL/E – Cable entry grommets, type KDT/xE – Snap-on / screw-on mounting 14 15 16 16 17 18–19 20–21 KDL cable entry system 23–38 – Advantages – Overview – Selection table...
Open the catalog to page 4– Overview – Selection table KDP/N (possible combinations of cable entries) – Selection table KDP-Multi (possible combinations of cable entries) – Material data KDP/N and KDP-Multi – Cable entry plate plastic, type KDP/N 24 – Cable entry plate, type KDP 24-Multi – Snap-on / screw-on mounting type KDP/N – Mounting KDP-Multi snap-on mounting – Mounting KDP-Multi screw-on mounting 63 64–65 66 67 68–69 70–71 72–73 74–75 76–77 Cable entry plate KDP plastic, round 79–86 – Advantages – Overview – Selection table KDP/R (possible combinations of cable entries) – Material data KDP/R – Cable entry...
Open the catalog to page 5Contents Material data Assigning cut-out codes / KDP types / adapter plates Selection table Rittal Housing (Murrplastik cut-out codes) Selection table Sarel Housing (Murrplastik cut-out codes) Selection table Sarel/Ensto/Lohmeier Housing (Murrplastik cut-out codes) Control cabinet floor sheeting, type SBB Blanking plate plastic, type BP Discharge plate, type KDL-AB and KDL/N-AB Blanking plate type BP xx ALU / V4A (metal design) Adapter plate Rittal Adapter plate Sarel Adapter plate Lohmeier Adapter plate Ensto Strain relief / cable fixing plate 132 133 134 135 136 137 138 139 140 141 142...
Open the catalog to page 6Material data for the accessories programme/for individual components (Part 2) Advantages Type KGM (plastic lock nut) Type GM (metal lock nut) Type BSTK (plastic dummy plug) Type BST (metal dummy plug) Type KRR (plastic reducing bush) Type RR (metal reducing bush) Type ER/EG (metal extension) Type OR-NBR (O-ring) Angle bracket, type BWM Conduit clamp, type SS Conduit clamp, type SSG Spiral tape, type SB/SBF Fixing rivets, type BN / Assembly tool, type BN Cable tie, type KB / KBM / KKB Cable tie, type BF Screwed holder, type SH Type KH (screwed and adhesive holders) 191 192 193–194 195 196...
Open the catalog to page 7Introduction Cable entry and cable holding systems KDL – for pre-assembled cables Our cable entry systems are designed for inserting preassembled cables and electrical conduits in divider walls, junction boxes, control cabinets and much more. Example applications: interior use, driver‘s cabs, in control cabinet, plant or machine construction. type KDL KDP – for cables without plugs The cable insertion panel is a routing and fastening system for cables without connectors and pneumatic hoses. Example applications: interior use, driver‘s cabs, in control cabinet, plant or machine construction....
Open the catalog to page 8For years, Murrplastik Systemtechnik GmbH has provided cable entry systems, cable entry panel systems, strain relief plates and cable holding systems. Right from the beginning priority was given to a systematic approach. The priority has always been to design "products which provide definite application advantages to the customer". The KDL cable entry system has been developed to make it much easier for end customers to route pre-assembled cables e.g. measurement, servo cables, computer cables and bus systems. During the design process, considerable emphasis was given to the need for a...
Open the catalog to page 9Cable entry plates for pre-assembled cables 10
Open the catalog to page 10System overview KDL / E cable entry system The KDL/E cable entry system represents further development of the third KDL generation. The advantage here is quicker assembly at double the capacity. Optionally, the KDL/E can additionally be snapped in. Page 13 KDL cable entry system The KDL cable entry system is a split system that allows pre-assembled cables to be routed into an enclosure without disassembling the connectors. Page 23 KDL / EMC cable entry system The KDL/EMC is the metal version of the KDL. Sheath currents of shielded cables can be simply discharged in several different ways...
Open the catalog to page 11KDL/E cable entry system 13
Open the catalog to page 13KDL / E cable entry system Advantages We go at everything head first 14 Even faster and simpler assembly of pre-fabricated conduits. The KDL/E replaces the well established KDL/N model. The single-piece frame no longer needs to be joined together. The provided catch hooks significantly speed up mounting of the entire plate, e.g. on the control cabinet. Vario grommets reduce the need for grommets with different diameters. This ultimately means significantly simpler and quicker assembly in general. ✔ Cable insertion without interruption ✔ Simple mounting ✔ Single-piece frame ✔ Snap-in from...
Open the catalog to page 14Overview Cable entry system, type KDL / E The KDL / E cable entry system represents further development of the third KDL generation. The advantage here is quicker assembly at double the capacity. Optionally, the KDL/E can additionally be snapped in. Page 17 Cable entry grommets, type KDT/xE In conjunction with the KDL / E cable entry system, the KDT/xE cable entry grommet can be used to easily route pre-assembled cables e.g. in control cabinets. Page 18 Snap-on mounting Screw-on mounting Detailed construction and assembly instructions for the snap-on/screw-on fittings. Page 20 15
Open the catalog to page 15All MURRPLASTIK SYSTEMTECHNIK catalogs and technical brochures
-
MP 35
9 Pages
-
MP 32
16 Pages
-
MP 32.2, MP 32.3 Alu
17 Pages
-
MP 3000
10 Pages
-
MP 20.2
8 Pages
-
MP 15
8 Pages
-
MP 14
8 Pages
-
MP 10.1
8 Pages
-
R-Tec Liner
2 Pages
-
Type PR/SV
2 Pages
-
Type USH/D
2 Pages
-
Type UH
2 Pages
-
Type EW
2 Pages
-
Labelling-Systems
240 Pages
-
Cable drag chain systems
371 Pages
-
Cables
84 Pages