MGJ6 14mm Series Murata Power Solutions 10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters SELECTION GUIDE FEATURES ■ Patents protected ■ No opto feedback ■ Optimised bipolar output voltages for IGBT/ SiC & MOSFET gate drives ■ Configurable dual outputs for all gate drive applications: +15V/-5V, +15V/-10V & +20V/-5V outputs ■ UL60950 Reinforced isolation to 690Vrms Recognition pending ■ IEC 61800-5-1 recognition pending ■ Characterised dv/dt immunity 80kV/^s at 1.6kV ■ Characterised partial discharge performance ■ 14mm Creepage and clearance ■ Ultra low coupling capacitance 13pF ■ DC link voltage 3kVDC ■ 5V, 12V & 24V input voltages ■ 105°C operating temperature Input Voltage Range V Typical Application See page 3 1. Components are supplied in tape and reel packaging, please refer to package specification section. Orderable part numbers are MGJ6DXXXXXXWMC-R7 (25 pieces per reel), or MGJ6DXXXXXXWMC-R13 (140 pieces per reel). 2. See ripple & noise test method. All specifications typical at Ta=25°C, nominal input voltage and rated output current unless otherwise specified.

MGJ6 14mm Series10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters SELECTION GUIDE (Continued) GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units

MGJ6 14mm Series10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters TEMPERATURE CHARACTERISTICS

MGJ6 14mm Series10.2kVDC Isolated 6W Gate Drive SM DC-DC ConvertersAPPLICATION NOTES Start-up times Typical start up times for this series, with no additional output capacitance are: Output capacitance must not exceed:

MGJ6 14mm Series 10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters APPLICATION NOTES (Continued) Schematic for driving IGBT, SiC & MOSFET MGJ DC-DC CONNECTIONS FOR DRIVING IGBT DEVICES MGJ DC-DC CONNECTIONS FOR DRIVING SiC DEVICES MGJ DC-DC CONNECTIONS FOR DRIVING MOSFET DEVICES

MGJ6 14mm Series 10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters TECHNICAL NOTES ISOLATION VOLTAGE ‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Murata Power Solutions MGJ6 series of DC-DC converters are all 100% production tested at 10.2kVDC for 1 second and have been qualification tested at 10.2kVDC for 1 minute. A question...

MGJ6 14mm Series10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters EFFICIENCY VS LOAD

MGJ6 14mm Series10.2kVDC Isolated 6W Gate Drive SM DC-DC ConvertersDERATING GRAPHSDerating curves are based on IPC-9592. With no derating some components may be operating at the manufacturers maximum temperature ratings.MGJ6D05XXXXWMC 100 90 80 70

MGJ6 14mm Series10.2kVDC Isolated 6W Gate Drive SM DC-DC ConvertersEMC FILTERING AND SPECTRA FILTERING The following filter circuit and filter table shows the input filters typically required to meet conducted emissions limits for EN 55022 curve B using Quasi-Peak (pink line) and average (green line) detectors according to CISPR 22. The following plots show measurements of the positive (L1) and negative (L2) inputs for both Quasi-peak limit B adherence and Average limit B adherence. If a high dv/dt above 80kV/us is expected from output to input it is advised that a common mode filter is used...

MGJ6 14mm Series 10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters EMC FILTERING AND SPECTRA MGJ6D24XXXXWMC ( (Quasi-Peak)

MGJ6 14mm Series10.2kVDC Isolated 6W Gate Drive SM DC-DC ConvertersPACKAGE SPECIFICATIONS PIN CONNECTIONS MECHANICAL DIMENSIONS All dimensions in mm (inches), Controlling dimensions is mm. Tolerance (unless otherwise stated) ±0.25 (0.010). Components shown for reference only.

MGJ6 14mm Series 10.2kVDC Isolated 6W Gate Drive SM DC-DC Converters TAPE & REEL SPECIFICATIONS REEL OUTLINE DIMENSIONS REEL PACKAGING DETAILS GOODS ENCLOSURE SECTION Tape & Reel specifications shall conform with current EIA-481 standard Unless otherwise stated all dimensions in mm(inches) Controlling dimension is mm # Measured at hub ## Six equi-spaced slots on 180mm/7” reel Product Orientation Pin 1, located nearest to Reel Quantity: 7” - 25 or 13” - 140 Carrier tape pockets shown are illustrative only - Refer to carrier tape diagram for actual pocket details TAPE OUTLINE DIMENSIONS COVER TAPE...