POWER-MISER & POWR-PRO PUMP SYSTEMS On Demand Live Power Hydraulics Off Mode Operation Increases Fuel Savings Powr-Pro Shown

POWER-MISER & POWR-PRO PuMP SyStEMS On-dEMand lIvE POWER hydRaulIc hydRaulI SyStEMS REady tO WORk WIth a k SInglE flIP Of thE SWItch. tch. The pump can be driven by eiTher The engine crankshafT or flyfly wheel pTo and conTains no T Tains cluTches or gears To engage or disengage, Thus providing increased producTiviTy for all solid wasTe packers and oTher mobile power applicaTions. applica Power-Miser Powr-Pro LOWER OPERATING COSTS are achieved when the system is operated in the off mode. Only enough oil flow to lubricate the pump is permitted. When off the pump requires extremely low horsepower...

PuMP fEatuRES and cOnStRuctIOn M SERIES ShOWn Dowel Pin Construction Cast Iron 3-Piece Construction System Matched Wearplates, Pressure Balance Seals And Shaft Seals Premium Heavy-Duty Roller Bearings Solid, One Piece Shafts With Entrapped Key Built-in Test Ports Retainer Rings Standard Bronze pressure balanced wear plates with Teflon® coating Gears machined for highest efficiency and lowest noise. Highest Grade Fasteners in the Industry with Anti-Corrosion Coating Protection and Rolled Threads all casT iron Three piece consTrucTion • pressure To 3000 psi • sysTem maTched componenTs provide for...

MOdEl nuMbER cOnStRuctIOn PM40 – 07 c f S l – M – a – 63 – b pump model pl14 (not available w/ppv) pl19 pl23 For Replacement Pump Only pl25 Pump Prefix is: pm27 PML1– ]]] or PMM1– ]]] pm31 (Delete model coding after pm35 Rotation) pm40 bleed valve** a — no bleed valve b — 2 gpm (8 lpm) flow conTrol valve* 00 — no option vp-10 (fixed) 28 — 28 gpm (106 lpm) 33 — 33 gpm (125 lpm) 36 — 36 gpm (136 lpm) 40 — 40 gpm (151 lpm) 52 — 52 gpm (197 lpm) 55 — 55 gpm (208 lpm) 63 — 63 gpm (238 lpm) VP-15 (Adjustable) 15 — 5 gpm (19 lpm) to 50 gpm (180 lpm) hose kiT a — no hose Kit h — for ppv only powr-pro(p)...

POWR-PRO INSTALLATION DIMENSIONS /O-RING BOSS PORT. FOR O-RING BOSS PORT. FOR FLAT ROOT SIDE FIT FRONT COVER O-RING BOSS PORT. FOR O-RING BOSS PORT. FOR Muncie Power Products, Inc.

POWER-MISER INSTALLATION DIMENSIONS FLANGE SHOWN REAR VIEW FLAT ROOT SIDE FIT Muncie Power Products, Inc.

PuMP OutPut VP10-* FLOW CONTROL ASSEMBLY AVERAGE OUTPUT – U.S. GALLONS AT 2500 PSI (175 BAR) FLOW RATE OUT OF VALVE – GPM (LPM) PUMP SIZE AVERAGE OUTPUT – U.S. GALLONS AT 2500 PSI (175 BAR) PUMP SIZE Note: Flow control orifices should be sized such that they bypass no higher than 50% of the desired control flow. Muncie does not promote specific manufacturers’ brands of oil. Recommendations below are guidelines; consult oil manufacturer for exact application needs. viscosity range: viscosity minimum: 50-60 sus (7.5-10.5 cst) viscosity optimum continuous: 60-100 sus (10.5-21.6 cst) viscosity maximum...

OnE-yEaR PuMP W WaRRanty The Muncie Cast Iron/Roller Bearing Pump Series “L & M” is warranted against any defect in material and workmanship which existed at the time of sale by Muncie, according to the following provisions, subject to the requirements that the Pump must be used only in accordance with catalogue and package instructions, and the warranty card must be filled out and returned to Muncie within ten days after the pump is installed. The Pump is warranted for a period of one-year from the date of instal installation. If during the warranty period the Pump fails to operate to Mun Muncie’s...