Concrete Vibrators Brochure
8Pages

www.multiquip.com Concrete Vibrators Flex-shaft, high-cycle and Micon computer-controlled

Flex-shaft concrete vibrators Quick disconnect knob for easy shaft removal Large vibration isolated handles protect the motor and operator Cassette-style motor improves durability and performance by minimizing friction and enabling the motor to maintain optimum RPM. Models range from 1 to 3 HP. ¡ Ergonomic design with swivel shaft connection. ¡ Compatible with entire range of steel heads and all rubber heads except 2¾" long type rubber head. ¡ Quick disconnect knob for easy shaft removal ¡ Powered by 2.1HP Honda 4-stroke engine with gear reduction for more torque than direct-drive models....

There’s a size and model for every application... Two shaft diameters and seven power heads allow you to match the equipment to the job. Round head radiates vibrations in all directions Case hardened tip for extra durability Forged eccentrics mounted on high speed ball bearings Double seals on shaft end Extra thick shell (up to 0.280") resists wear Industry’s strongest outer casing constructed of steel flat wire covered by alternating layers of wire mesh, fabric and rubber Coiled flat wire reinforcement keeps the shaft from kinking Inner core is wound from high carbon spring wire to resist...

MGX-Series Concrete Vibrators DOUBLE INSULATED — NO GROUND NECESSARY Cooling Fan Intake Discharge Greatly reduced airborne contamination.The sealed fan acts as a suction for air taken in from the rear, passed over the motor for cooling, and discharged at the rear again. 120 Volt Models 240 Volt Models Amps 120V (240V) Watts Head in. (mm) Shaft Dia. in. (mm) Amplitude in. (mm) Frequency Hz (vpm) Shaft Length ft. (m) Overall Length ft. (m) Motor Weight lb. (kg) Shaft/ Head Weight lb. (kg) Total Weight lb. (kg) MGX12325 MGX22325 3.8 (2.1) 280 .905 (23) .79 (20) .047 (1.2) 12,000 to 15,500 (200...

High-cycle concrete vibrators Multiquip’s High-Cycle Vibrators are designed for use in lowslump concrete where consistent power is needed to liquefy and move a stiff mix into corners and around rebar, or for any job where extended length vibrators are required. High-cycle vibrators (180 Hz) use a special three-phase, low-induction electric motor, located within the vibrating head. This close coupling translates into high efficiency—Mikasa High-Cycle Vibrators retain at least 95% of their power under load. Productivity is maximized due to the high centrifugal force and high frequency of the...

Micon high-cycle vibrators Multiquip’s Computer-Controlled Micon Concrete Vibrators are perfect for “zero” slump concrete applications, providing a higher level of consistent frequency than any other vibrator on the market today. Multiquip—the first with computer-controlled concrete vibrators. Conventional concrete vibrators have noticeably reduced motor RPM and frequency as soon as they are placed in the concrete. Multiquip’s Micon controller immediately sends more power to the head when it senses resistance that could cause the vibrator to slow down, ensuring that higher RPM and frequency...

© COPYRIGHT 2011, MULTIQUIP INC. All features and specifications are subject to change without notice. MVC-1154 Rev. M (01-11) MULTIQUIP INC. POST OFFICE BOX 6254 CARSON, CA 90749 310-537-3700 • 800-421-1244 FAX: 310-537-3927 E-MAIL: mq@multiquip.com www.multiquip.com Your Multiquip dealer is: Micon high-cycle vibrators — Specifications The Micon controller uses standard 120 volt, 60 cycle current; it converts this to 58 volt, 400 cycle current for use by the vibrator motor. The controller receives constant feedback information from the motor, allowing it to supply the exact amount of power...