DE iTECH
8Pages

{{requestButtons}}

Catalog excerpts

DE iTECH - 1

nF»TCI—LJ IMPULSE \ THERMAL MASS TECHNOLOGYV TECHNOLOGY Refrigeration dryers with Energy Saving Impulse Technology and Thermal Mass

Open the catalog to page 1
DE iTECH - 2

Refrigeration dryers with Energy Saving Impulse Technology and Thermal Mass With the introduction of DE iTECH, the new generation of energy-saving refrigeration dryers, MTA not only renews its product offering for the compressed air treatment but also reinterprets the concept of thermal storage operation, that made the international success of the DE Hybrid dryers. The new Impulse Technology offers important advantages in terms of energy saving, reliability and operating costs as the DE iTECH dryer is able to adapt itself to the real needs of the compressed air system. The regulation system...

Open the catalog to page 2
DE iTECH - 3

UNBEATABLE ENERGY EFFICIENCY, LOW PRESSURE DROPS, MAXIMUM RELIABILITY, SYSTEM SIMPLIFICATION: THESE ARE THE ADVANTAGES OF MTA DRYERS. IMPULSE TECHNOLOGY ENERGY SAVING This revolutionary design matches energy consumption to the work load to achieve energy savings while in operation. Thanks to some sensors placed on the refrigeration and on the compressed air circuits, the microprocessor controls the dryer operation granting the most effective method of compressed air drying. • For high/medium flows, the dryer applies the Impulse Technology to regulate its drying capacity. • For low air...

Open the catalog to page 3
DE iTECH - 4

Enhanced Energy Savings ENERGY SAVING COMPARISON ENERGY SAVING CALCULATIONS Normally a refrigeration dryer is sized to reach its nominal performance even in the most extreme conditions. In reality, these conditions are rarely achieved and the dryer works at partial load for most of its operating life. This is due to both the high variability of the compressed air flow of industrial plants and for the average operating temperature that normally is lower than the temperature used to select the dryer itself. Only a dryer capable to adapt its working cycle to the real working conditions can...

Open the catalog to page 4
DE iTECH - 5

ENERGY SAVING ALSO IN CLASS 5 APPLICATIONS Thanks to the particular technology of the DEiTech exchanger and then to the extremely low pressure drops, it has been possible to extend the flow in CLASS 5 with still competitive pressure drops: • The same DEiTECH unit can satisfy a wide range of application needs, ensuring energy saving when the dryer works in partial load conditions not only in CLASS 4 but also in CLASS 5 (where HGBV dryers typically waste energy). • Even with variable working conditions or ambient temperature the Impulse Technology let the DEiTECH to control accurately both...

Open the catalog to page 5
DE iTECH - 6

ELECTRIC POWER AND CONTROL PANEL The control section is electrically isolated from the power section through a transformer. On DEiT 140270 the power section is fitted with an interlocked door main switch to prevent access while power supply is ON. Electrical equipment is compliant with EN 60204-1 and electrical panel protection degree IP54 compliant with EN 60529 (DEiT 140-270). The dryer is tested for electromagnetic compatibility in accordance with applicable EMC standards. A phase monitor (DEiT 165–270) provides protection against phase loss and phase reversal. HIGH EFFICIENCY HEAT...

Open the catalog to page 6
DE iTECH - 7

Technical data Airflow CLASS 4 dew point ≤ 3 °C Power supply Nominal absorption power Nominal flow rate Nominal flow rate Data refers to the following working conditions: air FAD 20 °C / 1bar A, pressure 7 bar(g), ambient temperature 25 °C, air inlet temperature 35 °C, according to ISO 8573.1 standard. Weights are net (without packing and for timed drain confirguration). Refrigerant fluids: R134a (DEiT 003-080), R404A (DEiT 101-270). Protection class IP22. Maximum working pressure 16 bar(g); maximum ambient temperature 50 °C; maximum inlet temperature +70 °C (DEiT 003-080), +60 °C (DEiT...

Open the catalog to page 7
DE iTECH - 8

The images of the products in the document are for illustrative purposes only and therefore do not have any contractual value. M.T.A. S.p.A. Viale Spagna, 8 ZI 35020 Tribano (PD) Italy MTA Deutschland GmbH Tel: +49 (2157) 12402 - 0 www.mta.de info@mta-it.com www.mta-it.com Milan branch office Tel. +39 02 95738492 Novair-MTA, S.A. (España) Tel: +34 938 281 790 www.novair-mta.com SC MTA ROMÂNIA Srl Tel: +40 723 022023 www.mta-it.ro MTA is represented in over 80 countries worldwide. For information concerning your nearest MTA representative please contact M.T.A. S.p.A. The continuous...

Open the catalog to page 8

All MTA S.p.A catalogs and technical brochures

  1. Aries Tech

    2 Pages

  2. Galaxy Tech

    2 Pages

  3. Taurus Tech

    2 Pages

  4. HAries Tech

    2 Pages

  5. HTaurus Tech

    2 Pages

  6. HCYGNUS TECH

    2 Pages

  7. phoenix plus

    2 Pages

  8. CYGNUS Tech

    2 Pages

  9. EURUS

    6 Pages

  10. NEWGEN Si

    6 Pages

  11. TWEevo

    2 Pages

  12. HAEevo

    2 Pages

  13. LiquiPro

    2 Pages

  14. LiquiPure

    2 Pages

  15. RWD

    1 Pages

  16. T3 laser

    4 Pages

  17. aqua free

    2 Pages

  18. neptune tech

    2 Pages

  19. c aries tech

    2 Pages

  20. TAEevo

    8 Pages

Archived catalogs

  1. CYGNUS

    2 Pages

  2. NEPTUNE/ME

    2 Pages

  3. ORION

    2 Pages

  4. TWE Evo

    8 Pages