Catalog excerpts
SF2 500 The SF2 series are designed for reservoir side-wall A major feature of these filters is that the filter ele- mounting applications, suitable for flow rates to 850 ment (situated under the oil level) can be changed l/min and filtration from 25 to 250 micron. without empting the reservoir; the valve is actioned by The design of the SF2 ensures an excellent perform- handwheel on the filter cover, to avoid accidental start ance in terms of low pressure drop and high dirt hold- up when the valve is closed, an antistart safety switch ing capacity. The SF2 filters are without bypass and...
Open the catalog to page 2MP Filtri - Filtration Technology Filter element: Materials Element material Nominal filtration Support tube: Support frames: Steel expanded metal Expanded metal MSeries Square wire mesh (filtration degree is defined in microns by the maximum diameter of a sphere corresponding to the mesh size). Filtering area Filter elements Filter body: Materials Head Pressure aluminium die casting Steel (only for SF2 535-540) A Series: Nitrile (Buna-N) V Series: Viton Anodized aluminium Óptional Flange Working temperature Anodized aluminium From -25 to +110°C For temperature outside this range, please...
Open the catalog to page 3MP Filtri - Specification Compatibility with fluids Filter head and bowls Filter elements compatible for use with: • mineral oils (types HH-HL-HM-HR-HV-HG as per ISO 6743/4) • water-based emulsions (types HFAE-HFAS as per ISO 6743/4) • synthetic fluids (types HS-HFDR-HFDS-HFDU as per ISO 6743/4) • water-glycol (types HFC as per ISO 6743/4) Ask for anodised version As per ISO 2943; suitable for mineral oils (types HH-HL-HM-HR-HV-HG as per ISO 6743/4) synthetic fluids (A and M series only) (types HS-HFDR-HFDS-HFDU as per ISO 6743/4) For water-based emulsions (type HFAE-HFAS as per ISO 6743/4)...
Open the catalog to page 4Selection & installation information Filter elment types M Series Metal mesh media, available in 25, 60, 90, 250 µm Example - M25, M60, M90 or M250 Please refer to individual pressure drop curves to obtain filter assembly pressure drop information The following filter sizing recommendations are based using a mineral oil fluid at 30 mm 2/s (cSt) with a maximum total filter assembly (housing and filter element) pressure drop of 8kPa (0,08 bar) Safety microswitch Min space required for servicing Filter Assembly Flow rate l/min Optional flange C1 dimn. “A” Port Size BSP/NPT/SAE ** Flow rates...
Open the catalog to page 5Selection & installation information Filter elment types M Series Metal mesh media, available in 25, 60, 90, 250 µm Example - M25, M60, M90 or M250 Please refer to individual pressure drop curves to obtain filter assembly pressure drop information The following filter sizing recommendations are based using a mineral oil fluid at 30 mm 2/s (cSt) with a maximum total filter assembly (housing and filter element) pressure drop of 8kPa (0,08 bar) ** Flow rates with 30 mm /s fluid viscosity ** Weight including filter element 2 Optional flange C1 dimn. “A” Filter mounting dimns. Flange Connections...
Open the catalog to page 6Selection & installation information Filter elment types M Series Metal mesh media, available in 25, 60, 90, 250 µm Example - M25, M60, M90 or M250 Please refer to individual pressure drop curves to obtain filter assembly pressure drop information The following filter sizing recommendations are based using a mineral oil fluid at 30 mm 2/s (cSt) with a maximum total filter assembly (housing and filter element) pressure drop of 8kPa (0,08 bar) ** Flow rates with 30 mm /s fluid viscosity ** Weight including filter element 2 Optional flange C1 dimn. “A” Port Size BSP/NPT/SAE Flow rate l/min...
Open the catalog to page 7Selection & installation information Filter elment types M Series Metal mesh media, available in 25, 60, 90, 250 µm Example - M25, M60, M90 or M250 Please refer to individual pressure drop curves to obtain filter assembly pressure drop information The following filter sizing recommendations are based using a mineral oil fluid at 30 mm 2/s (cSt) with a maximum total filter assembly (housing and filter element) pressure drop of 8k Pa (0,08 bar). Filter Assembly Safety microswitch Anti back flow valve screw Minimum space required for servicing Optional flange C1 dimn. “A” OUTLET FLANGE“A” Port...
Open the catalog to page 8Pressure drop information General Pressure drop versus flow rate curve information for both housing and filter elements is in accordance with ISO 3968 Filter assembly pressure drop - ∆p Total = ∆p Housing + ∆p Filter element Housing pressure drop - The housing pressure drop is proportional to the fluid density Filter element pressure drop - Filter element pressure drop is proportional to kinematic viscosity therefore always check the fluid operating temperature and fluid type to obtain the working viscosity according to the following formula: ∆p1 Filter element = (working viscosity/brochure...
Open the catalog to page 9Filter element pr essur e drop The curves were obtained using a mineral oil with a kinematic viscosity of 30 mm2/s (cSt).The ∆p varies proportionally to the fluid kinematic viscosity. 150 200 Flow rate I/min 150 200 Flow rate I/min Flow rate I/min 300 400 Flow rate I/min 600 Flow rate I/min Flow rate I/min
Open the catalog to page 10Ordering code example SF2 Filter condition indicator (Use SF 510 filter element code) This example shows how order a complete filter with features based on the customer request. With threaded hole only With hole + plug Visual (axial vacuumeter) Visual (radial vacuumeter) Electrical (change-over contacts vacuumeter) Filter elements Nitrile (Buna-N) Viton Square wire mesh Port option Without microswitch, without handwheel With microswitch, without handwheel (505, 510, 535, 540) With microswitch, with nylon handwheel (500, 501, 503, 504) With microswitch, with steel handwheel (500, 501, 503,...
Open the catalog to page 11Head Quarter : MP FILTRI S.p.A. Italy Via Matteotti, 2 20060 Pessano con Bornago (Milano) Italy Tel. ++39.02/95703.1 Fax ++39.02/95741497-95740188 email: sales@mpfiltri.com http://www.mpfiltri.com GREAT BRITAIN MP FILTRI U.K. Ltd. Bour ton Industrial Park Bour ton on the Water Gloucestershire GL54 2HQ UK Phone: 01451-822522 Fax: 01451-822282 email: sales@mpfiltri.co.uk http://www.mpfiltri.co.uk GERMANY MP FILTRI D GmbH Am Wasser turm 5 D-66265 Heusweiler/Holz Phone: 06806/85022-0 Fax: 06806/85022-18 email: mpfiltrink@aol.com FRANCE MP FILTRI FRANCE B.P. 325 01603 Trevoux Cedex Tel:...
Open the catalog to page 12All MP Filtri catalogs and technical brochures
-
MULTI-COMPONENTS
31 Pages
-
LMS/LDS Series
17 Pages
-
LMC/LDC Series
17 Pages
-
LMG Series
21 Pages
-
ACCESSORIES
28 Pages
-
BELL HOUSING
72 Pages
-
CLOGGING INDICATORS
24 Pages
-
COUPLINGS
46 Pages
-
CONTAMINATION CONTROL SOLUTIONS
140 Pages
-
Return / Suction Filters
76 Pages
-
SPIN-ON FILTERS
76 Pages
-
Stainless Steel Filters
102 Pages
-
Low & Medium Pressure Filters
168 Pages
-
High Pressure Filters
160 Pages
-
Suction Filters
72 Pages
-
Return Filters
230 Pages
-
FHD - DUPLEX
17 Pages
-
FHF 325 - MANIFOLD
14 Pages
-
FHB - MANIFOLD
16 Pages
-
FHM - MANIFOLD
21 Pages
-
FHP
19 Pages
-
FMP
14 Pages
-
Spin-On Filter
78 Pages
-
Stainless Steel
20 Pages
-
LMP 124
6 Pages
-
MRSX
12 Pages
-
MSH
4 Pages
-
CS - CG - CW - CT
2 Pages
-
MPS
8 Pages
-
LMP 952 - 954
6 Pages
-
LMP 900 - 901
4 Pages
-
LMD 400 - 401 - 431 DUPLEX
8 Pages
-
LMP MULTIPORT
8 Pages
-
FMM 050 - FHA 051
6 Pages
-
FMP 039
4 Pages
-
Clogging Indicators
26 Pages
-
SF2 250 - 350
4 Pages
-
Suction Strainer
7 Pages
-
FRI
10 Pages
-
MPI
8 Pages
-
MPH
18 Pages
-
MPT
15 Pages
-
filter element CH
1 Pages
-
MST
4 Pages
-
STR
4 Pages
-
RF2
4 Pages
-
MPF
20 Pages
-
LMP 400 - 430
10 Pages
-
LMP 210
5 Pages
-
LMP 110-120-123 MULTIPORT
25 Pages
-
FAS
4 Pages
-
SF2 250
8 Pages
-
Structural components
78 Pages
-
SA - SAP
10 Pages
-
STR
4 Pages
-
Condition monitoring products
14 Pages
-
Pressure filters
116 Pages
-
In-line filters
108 Pages
-
Structural components
64 Pages
-
Accessories
68 Pages
-
Catalogue
19 Pages