Product Data Sheet Actuator FD60 FD60 is a quiet and powerful actuator up to 6000N thrust, designed for use in furniture application. Our T control box, which can be perfectly attached and integrated to FD60, is available for customers to choose. Features - Main applications: Furniture - Input voltage: 24V DC / 12V DC - Max. load: 6000N (push) / 4000N (pull) - Typical speed at no load: 33.3 mm/sec - Typical speed at full load: 2.9 mm/sec (6000N load) - Stroke: 50 ~ 300 mm - Noise level: ≦50dB - IP Protection level: IP42 - Color: Black - Preset limit switches - Duty cycle: 10%, max. 2 min. continuous operation in 20 min. - Ambient operation temperature: -20°C ~ +65°C - Certified: CE Marking, EMC Directive 2014/30/EU, UL 962 Standard for Household and Commercial Furnishings. Options - Positioning signal feedback with Hall effect sensor x 1 - Positioning signal feedback with Hall effect sensor x 2 - Mechanical push only extension tube - Mechanical brake - Turn 90° Pivot orientation of rear connector

Performance Data Model No. **Typical Speed (mm/s) No load Full load **Typical Current (A) No load Full load Load (N) Push / Pull Load Push Load Remarks: * The self-locking ability is performed by short circuit the motor terminals when the actuator is powered off. All MOTECK compatible control boxes are designed with this feature. Mechanical brake in push direction is available upon request, to further enhance the self-locking ability to maximum load. ** The typical speed or typical current means the average value neither upper limit nor lower limit. The performance curves are made with typical...

Pivot orientation Note: As an example in 0° orientation for rear connector. Direct-Cut cable DL2 Actuator 300 Hand control Power supply Hand control Power supply

Installation Dimension ● Retracted length (A) Rear connector code Front connector code 1, 5, 8 5 (with crank function) Available stroke (S) range = 50 ∼ 300 mm Extended length = S + A ● Front connector 1: Plastic 2: Drilled hole with brass bushing 7: Drilled hole with nylon bushing Diameter of pivot without bushing (D1) Front connector code Width with bushing (W1) Diameter of pivot with bushing (D2) Width with bushing (W1) ● Rear connector 1: Plastic 5: Metal (with crank function) ø5 D1 D2 Diameter of pivot with bushing (D2) Rear connector code Diameter of pivot without bushing (D1)

Compatibility Product - With dual Hall effect sensors - With Moteck F-type 6-pin DIN plug - 12V DC motor - With dual Hall effect sensors - With Moteck F-type 6-pin DIN plug - With dual Hall effect sensors - With Moteck L3-type minifit 6-pin plug - With Moteck Direct-Cut cable TL2* Hand control - Without positioning sensor - With Moteck L3-type minifit 6-pin plug - Without Hall effect sensor - With Moteck F-type 4-pin DIN plug - With Moteck Direct-Cut cable DL2* TSW1 Switching mode power supply - With Moteck Direct-Cut cable DL2 or TL2 Remarks: * Connect Direct-Cut cable to DC power supply and...

Cable Plug With Moetck F-type or L3-type plug (Required to be connected to the control box): ● Without Hall effect sensor M- M+ F-type 4-pin DIN plug ● With dual Hall effect sensors GND Note: Connect Pin (M+) to “+” & Pin (M-) to “-“ of DC power, the actuator will extend. With Direct-Cut cable DL2 or TL2 (NOT required to be connected to any control box): ● Hand control connector: with Moteck U-type female connector 1 drive 5-pin connector (Moteck pinout: C-DIN-52H) 5-pin connector (Moteck pinout: C-DIN-51H) Note: Connect pin (M1+) to "+" & pin (M1-) to "-" of DC power, the M1 actuator will extend....

Wiring Wire definitions: ● Without positioning sensor feedback Power White Note: 1. Connect White(M+) to ‘+’ & Black(M-) to ‘-’ of DC power, the actuator will extend. ● With Hall effect sensor Single Hall effect sensor Power Dual Hall effect sensors Power Note: 1. Connect Blue(M+) to ‘+’ & Brown(M-) to ‘-’ of DC power, the actuator will extend. 2. Hall effect sensor resolution 3. Voltage input range (VCC): 3.5~20V 4. Output voltage of signal (Data) = Input voltage of VCC 5. Hall signal data VCC Actuator extends Actuator retracts Certifications The FD60 actuator is compliant with the following...

Motor and Spindle type Retracted length Extended length Front connector 1: Plastic 2: Drilled hole with brass bushing 3: Drilled hole 5: Metal 7: Drilled hole with nylon bushing 8: Enhanced metal (Refer to page 4) Rear connector 1: Plastic 2: Metal 5: Metal (with crank function) (Refer to page 4) Positioning feedback Blank: None HS3: Hall effect sensor x 1 HS4: Hall effect sensor x 2 Blank: None PO: Mechanical push only extension tube BK: Mechanical brake (Note: Multiple choice is allowed) 0: 300 mm straight 1: 1000 mm straight 2: 450 mm with 300 mm coiled A: Direct-Cut cable DL2, without control...