201 Series
6Pages

The Specialist In Drum Handling Equipment 201 Series Wheeled Portable Drum Rollers Mix Contents of Closed Steel Drum • Use common steel drum for mixing No permanent container to purge between batches Use separate drum for each batch Agitate your drum’s contents without even opening the drum! Incorporate important stratified ingredients and eliminate sediment in the bottom of your drum. Mixing in closed drums eliminates the hazards, worker exposure, and messy cleanup associated with insertion mixers. This compact, portable mixer and drum cradle rolls a closed drum to agitate the 40” contents. You may also dispense directly 101.6 cm from your drum through a faucet. The builtin tipping bar provides leverage to ease loading and unloading. The sides and back are enclosed to protect the drive. Drum Sizes • Roll a 6” to 28” (15.2 to 71 cm) diameter drum Up to 38” (97 cm) tall. Relocate wheels to accommodate various steel drum sizes. The tipping lever will ONLY engage a drum 30” (76.2 cm) or taller Kick Stand Deploy Kick Stand to support drum roller in upright position. Fixed speed models roll a 22.5” (57.2 cm) diameter drum at 20 RPM (16 RPM on 50Hz models) Variable speed models roll a drum from 15 to 24 RPM (13 to 20 RPM on 50Hz models) Dispense Directly from Drum Drain the contents of a drum directly into a smaller container for use as needed. A closed faucet can be in place while the drum is rotated. Capacity of Wheeled Models • • Liquid load: 500 Lb. (227 kg) Dry load 300 Lb. (136 kg) Maximum ambient operating temperature • Engage Top Rim Hook to help in tipping it over into rolling position. Options and Accessories Roll a 1 to 5 Gallon Can Kit # 1-5P Install this Idler Attachment kit to extend the usefullness of your drum roller. Easily attached with 4 bolts, the spacers adjust to roll a 1 to 5 gallon (4 to 20 liter) cylindrical can. Rolls a 5-gallon (20L) can at approximately double the RPM of a 55-gallon (210L) drum. Roll a Plastic Drum Option # POLY-201 Factory installed option to roll a plastic drum on portable drum roller. • Extra wheels to support flexible softsided plastic drum • End stop to prevent drum from traveling • Chain to assist in pulling upright drum over into rolling position Simple Rock-Over Loading Built-in tipping lever facilitates loading. Frame shape and height make loading easier. Note: Tipping lever only engages drum 30” (76.2 cm) or taller. POLY-201 is NOT a drum roller by itself. Adds 62 Lb. (28.1 kg) to the ship weight and requires a skid. Internal Components Large sprockets and roller chain for years of reliable drum rolling. Kit for customer to install on wheeled 201 Series drum roller. morsedrum.com

The Specialist In Drum Handling Equipment Custom Stainless Steel Portable Drum Rollers 201 Series Wheeled Portable Drum Rollers Construction and Design Features Bottom shows working parts and their accessibility 1. Built-in tipping lever extends to assist in loading drum Chine hook Variable speed control Two 3” (7.6 cm) swivel casters for mobility. Bearings support two jack shafts. Standard motor is 1/2 HP, 60Hz, 115V, 1800 RPM, single phase, ball-bearing, totally enclosed type with manual reset overload protection, switch, cord and plug. Air motors and other electric motor voltages and...

201 Series Wheeled Portable Drum Rollers The Specialist In Drum Handling Equipment Steps To Use Morse Portable Drum Rollers (continued from page 2) D. Extend tipping lever (1) fully and push toward drum. Engage chine hook (2) on top rim of drum E. To raise kickstand (9), push tipping lever (1) toward drum to allow kick stand to clear the floor. Then pull yellow release handle (11) F. Pull fully extended tipping lever (1) to tilt drum roller over to horizontal rolling position G. Move drum roller into enclosure with interlock, connect power (8) and turn on H. Once rolling is complete, turn...

The Specialist In Drum Handling Equipment 201 Series Wheeled Portable Drum Rollers Guard Enclosure Kits with Safety Interlock Comply with OSHA Requirements (Drum Roller Sold Separately) Outside Post-To-Post Dimensions L52” x W40” x H63.25” (132 x 102 x 161 cm) Enclosures for Morse Portable Drum Rollers have a safety interlock to automatically shut off the drum roller when the gate is opened. Open the enclosure gate, place your drum onto the drum roller, then close the gate to allow operation. Connections are included for single-phase AC and for air powered models only. Customer to provide...

The Specialist In Drum Handling Equipment 201 Series Wheeled Portable Drum Rollers Fixed Speed Wheeled Portable Drum Rollers Model # Full Load Amp Draw Drum Roller Capacity Liquid Dry Contents Contents ** Handle Drum Diameter Maximum Control Package Guard Enclosure Drum OUTSIDE Enclosure Kit # Length Model # * RPM is based on standard 22.5” (57.15 cm) diameter 55-gallon (210 liter) drum. ** A shifting dry load exerts greater stress on the drum roller than the fluid motion of a liquid load. *** Noise Level: 92 dB at distance of 6 feet (1.8 m)

201 Series Wheeled Portable Drum Rollers The Specialist In Drum Handling Equipment Variable Speed Wheeled Portable Drum Rollers Model # Full Load Amp Draw Drum Roller Capacity Handle Drum Diameter Maximum Control Package Guard Enclosure Drum OUTSIDE Enclosure Kit # Length Model # Liquid Contents * RPM is based on standard 22.5” (57.15 cm) diameter 55-gallon (210 liter) drum. ** A shifting dry load exerts greater stress on the drum roller than the fluid motion of a liquid load. *** Noise Level: 92 dB at distance of 6 feet (1.8 m)ww