Single Stationary Drum Rollers The Specialist In Drum Handling Equipment Single Stationary Drum Rollers Save time, labor and money Blend ingredients right inside a sealed drum Eliminate transfer, clean-up, special vessels Ensure Homogeneity Maximum ambient operating temp: 140o F (60o C) OSHA Requires Enclosure with Safety Interlock (pg. 4) Loading Methods Variable Speed Control Packages Available for Model 1-5154-3 Rotate drums at any speed from 1 to 30 RPM. Find the best speed for each material. Some use high speed for initial mixing and low speed for prolonged agitation. Variable speed drum rollers are ideal for experimental use or where there is a variety of materials to be handled. Model 1-5154-3 shown rolls one drum Variable speed packages are not available for explosionproof drum rollers. Capacity: Liquid load: 1000 Lb. (455 kg) Dry Load: 300 Lb. (136 kg) at 20 RPM Get a drum horizontal with Morse model 160 Drum Truck. Then lift it with model 41 Drum Lifting Hook. A shifting dry load exerts greater stress on the drum roller than the fluid motion of a liquid load. Fixed Speed Drum Rollers Designed to rotate one drum at factory fixed drum speed of 20 RPM (16 RPM for 50Hz models), based on 22.5” (57 cm) diameter drum. Drum rolling speed of 20 RPM is good for most liquids... often used for paint, etc. Capacity: Liquid load: 1000 Lb. (455 kg) Dry load: 300 Lb. (136 kg) Stainless Steel Drum Rollers ROTATE VARIOUS DRUM SIZES: Designed to roll a steel drum 6” to 28” (15 to 71 cm) diameter and up to 40” (102 cm) long. Frame made of bead blast finished type 304 stainless steel. Welds NOT ground smooth or polished. Motor, gear box, coupling and bearings NOT stainless steel. The idler wheel assembly can be moved closer to the drive shaft for various drum diameters. Set screws at each wheel permit easy repositioning to support various length drums. Omni-Lift Drum Racker may also be used to place a steel drum onto your single drum roller. A powerful 1/2 HP motor drives an efficient worm gear reducer connected to a solid 1” (2.54 cm) diameter shaft to turn four 6” (15.2 cm) diameter neoprene drive wheels. The four idler wheels turn freely on roller bearings. The basic motor is a three phase, 230/460V, 60Hz, inverter duty motor. Explosion-Proof and air motors are also available. Motor controls are not included with the basic machines. Standard Stationary Drum Rollers are shipped without control, cord and plug and must be installed by an electrician according to local codes and customer’s preference. Morse Control Packages sold separately - page 3. Morse Guard Enclosure Kits with Safety Interlock sold separately - page 4. Grounding Strap: Spring steel grounding straps are standard to help drain possible static charge from drum. Base Dimensions: 24” x 58” (61 x 147 cm) Load with a MORStak Drum Racker Options ROLL A PLASTIC DRUM ROLL A 5-GALLON PAIL Option # 1-5-1 Option # POLY-1-5154 Factory Installed Kit # POLY-1-5154FI for you to install Idler Attachment to facilitate rolling 1 to 5 gallon size (3.8 to 18.9 liters) cylindrical cans or pails. Rolls a 5-gallon can at approximately double the RPM of a 55-gallon drum. It is easily removed to return to rolling drums. Install this option to roll a plastic drum on stationary drum roller. Includes extra wheels to support flexible soft-sided plastic drum, and end stop to prevent drum from traveling lengthways. NOTE: This is NOT a drum roller by itself. It is an OPTION to install on a Morse Drum Roller. morsedrum.com

Single Stationary Drum Rollers The Specialist In Drum Handling Equipment Control Packages Stationary Drum Rollers Motor Information 20 RPM or Add Morse Control Package for 1 to 30 RPM Variable Speed Motor Style 20 Vary with air flow & pressure Crate for Export of (1) Guard Enclosure Kit ** Explosion Proof motors are rated for Class I Group D, and Class II Groups F and G. Variable speed models are NOT available for hazardous areas. Crate for Export of (1) Drum Roller Crate for Export of (1) Drum Roller and (1) Control Package * ONLY NON-Explosion Proof AC Control Packages include a pre-wired control...

The Specialist In Drum Handling Equipment Single Stationary Drum Rollers Control Packages (Sold Separately) MADE IN USA Control Mast and the appropriate Control Box for each model Use power controls to start and stop drum rolling Position the control mast outside the Safety Enclosure on either the left or right side, or at the back of Drum Roller Control Mast and AC Control Box for Model 1-5154-1 or 2-5154-1 NEMA 4/12 for NON-Hazardous Areas Control Mast and AC Control Box for Model 1-5154-3 or 2-5154-3 NEMA 4/12 for NON-Hazardous Areas Includes Control Mast and Control Box with: Includes Control...

The Specialist In Drum Handling Equipment Single Stationary Drum Rollers Minimum Power Supply Required Power Supply Control Package for 1-5154-E1, Explosion-Proof Control Package for 1-5154SS-E1, Explosion-Proof Control Package for 1-5154-E1, Explosion-Proof Control Package for 1-5154SS-E1, Explosion-Proof Control Package for 1-5154-E1, Explosion-Proof Control Package for 1-5154SS-E1, Explosion-Proof Control Package for 1-5154-E3, Explosion-Proof Control Package for 1-5154SS-E3, Explosion-Proof Control Package for 1-5154-E3, Explosion-Proof Control Package for 1-5154SS-E3, Explosion-Proof Control...

Single Stationary Drum Rollers The Specialist In Drum Handling Equipment Guard Enclosure Kits with Safety Interlock (Sold Separately) MADE IN USA Comply with OSHA Requirements with a Morse Guard Enclosure Kit (Sold Separately) Guard Enclosures for Morse Stationary Drum Rollers have a safety interlock to automatically shut off the drum roller when the gate is opened. Open the enclosure gate, place your drum onto the drum roller, then close the gate to allow operation. Connections are included for air powered model only. Control Package options provide controls and connections for AC models. Install...