DC/DC Converter K12T-10A, 16A Series Non-isolated & regulated 10A, 16A single output  High efficiency up to 96%  Operating ambient temperature range: -40℃ to +85℃  Input under-voltage protection, output short-circuit, over-current protection  High-speed transient response  Compact SMD package  EN62368 approved K12T-10A, 16A series is a 10A, 16A non-isolated switching regulator. The output voltage is accurately adjustable from 0.75V to 5.0V, and the product is featured with high efficiency, fast transient response, input under-voltage, output short circuit, over-current protection. They meet CLASS B of CISPR32/EN55032 EMI standards by adding the recommended external components and they are widely used in applications such as communications, computer network industry, power distributed architecture, workstations, servers, LANs/WANs and provide high current with fast transient response for high-speed chips such as FPGA, DSP, and ASIC. Selection Guide Input Voltage (VDC) Certification Voltage(VDC) (Range) Efficiency(%) Min./Typ. Nominal (Range) Notes: ① “P” indicates that the Ctrl pin is positive logic control, “N” indicates that the Ctrl pin is negative logic control; ② Exceeding the maximum input voltage may cause permanent damage; ③ The default output voltage is 0.75VDC, which can be adjusted to 1.2VDC, 1.8VDC, 2.5VDC, 3.3VDC, 5VDC. See Trim instructions for specific output voltage adjustment; ④ Unless otherwise specified, parameters in this table were measured under the 5VDC output voltage. Input Specifications Item Operating Conditions Input Current (full load/no-load) Nominal input voltage Start-up Voltage Under-voltage Protection Reverse Polarity Input Input Filter Capacitance filter Module on Ctrl pin open or pulled high (Vin-2.5V ~ Vin) Ctrl pin open or pulled low to GND (0 ~ 0.5VDC) Ctrl pin pulled low to GND (0 ~ 0.5VDC) Ctrl pin pulled high (Vin-2.5V ~ Vin) Input current when off Notes: * 1. The Ctrl pin voltage is referenced to GND; 2. Unless otherwise specified, parameters in this table were measured under the 5VDC output voltage. Output Specifications Item Operating Conditions Voltage Accuracy Full load, nominal input voltage MORNSUN Guangzhou Science & Technology Co., Ltd. reserves th

DC/DC Converter K12T-10A, 16A Series Linear Regulation Full load, input voltage range Load Regulation Nominal input, 0% -100% load Ripple & Noise* 20MHz bandwidth, nominal input, 100% load Trim Sense Transient Recovery Time Nominal input, 50%-100%-50% load step change, di/dt=2.5A/us, with external 470 µF polymer capacitors Over-current Protection Nominal input Short-circuit Protection Nominal input Temperature Coefficient Transient Response Deviation Continuous, self-recovery -- Notes: * 1. The “parallel cable” method is used for Ripple and Noise test, please refer to DC-DC Converter Application...

DC/DC Converter K12T-10A, 16A Series K12T-16A Series Temperature Derating Curves K12T-10A Series Efficiency Curves MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation

DC/DC Converter K12T-10A, 16A Series K12T-16A Series Efficiency Curves MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation

DC/DC Converter K12T-10A, 16A Series Remote Sense Application 1. Remote sense connection if not used Notes： 1. If the sense function is not used for remote regulation the user must connect the Sense to + Vo at the DC-DC converter pins and will compensate for voltage drop across pins only; 2. The connections between Sense and +Vo must be kept as short as possible, otherwise they may be picking up noise, interference and/or causing unstable operation of the power module. 2. Remote sense connection used for compensation PCB-tracks or cables/wires for Remote Sense must be kept as short as possible;...

DC/DC Converter K12T-10A, 16A Series Table 2 Selected based on the actual input current in application C2 Refer to the Cout in Table 1 3. Trim function for output voltage adjustment (open if unused) Table 3 Calculating Trim resistor (RT) values:： Fig. 4 TRIM resistor connection (dashed line shows internal resistor network) Notes: 1. RT : Resistance of Trim; Vo: The trim up voltage; 4. For additional information please refer to DC-DC converter application notes on www.mornsun-power.com Dimensions and Recommended Layout MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and...

DC/DC Converter K12T-10A, 16A Series Notes: 1. For additional information on Product Packaging please refer to www.mornsun-power.com. Packaging bag number: 58210071; 2. The maximum capacitive load offered were tested at input voltage range and full load; 3. Unless otherwise specified, parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH with nominal input voltage, 5VDC output voltage and rated output load; 4. All index testing methods in this datasheet are based on company corporate standards; 5. We can provide product customization service, please contact...