Patent Protection 1W, Fixed input voltage , 4200VAC or 6000VDC isolated & unregulated positive-negative dual/single output FEATURES • SIP package • High efficiency up to 81% • Reinforced insulation • The patient leakage current: Max 2pA • Isolation voltage: 4200VAC or 6000VDC • Operating temperature range:-400C to +850C • Internal surface mounted design • International standard pin-out • EN60601-1, ANSI/AAMI ES60601-1approval (1xMOPP/2xMOOP) • IEC60950 approval G_S-1WR2 & H_S- 1WR2 series meet reinforced Insulation requirements. They are specially designed for applications where require compact size., high isolation, low Isolation capacitor and low leakage current power. They are widely used in medical, electricity, IGBT driver and so on. They are suitable for: 1 Where the voltage of the input power supply is stable (voltage variation: ±i0%Vin); 2 Where isolation is necessary between input and output (isolation voltage ^4200VAC or6000VDC); 3 Where do not has high requirement of line regulation and the ripple & noise of the output voltage; Such as: Medical collection and isolation. High voltage collection circuit, IGBT-driven circuits, etc. Selection Guide MORNSUN GUANGZHOU SCIGNCG & TGCHNOLOGY CO.,LTD. MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyrigh

Input Specifications General Specifications Note: 1. Patient leakage current and reinforced insulation is based on a 250 VAC, 50/60 Hz system input voltage. 2. The UL certification (ANSI/AAMI ES60601-1, File No. E347375) of G_S-1WR2 & H_S-1WR2 series is approved, G_S-1WR2 & H_S-1WR2 series meets 1 xMOPP/2xMOOP when system input voltage is with 250VAC , 50/60Hz. Output Specifications MORNSUN GUANGZHOU SCIENCE & TECHNOLOGY CO.,LTD. MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation

DC/DC Converter G_S-1WR2 & H_S-1WR2 Series Physical Specifications Casing Material Package Dimensions Black flame-retardant and heat-resistant plastic (UL94 V-0) 19.50*9.80*12.50 mm Cooling Method EMC Specifications Conducted emission CISPR22/EN55022 CLASS B (see Fig. 5 for recommended circuit) Electrostatic discharge CISPR22/EN55022 CLASS B (see Fig. 5 for recommended circuit) Radiated emission Product Characteristic Curve 5VDC output Output Current Percent (Nominal Input Voltage) 40% 80% 60% Output Current Percent (Nominal Input Voltage) Output Voltage Accuracy Output Voltage Accuracy Other...

Design Reference 1. Typical application If it is required to further reduce input and output ripple, a filter capacitor can be connected to the input and output terminals, see Fig.3. Moreover, choosing suitable filter capacitor is very important, start-up problems may be caused by too large capacitance. To ensured the modules running well, the recommended capacitive load values as shown in Table 1. The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series...

Dimensions and Recommended Layout 1. Packing information please refer to Product Packing Information which can be downloaded from www.mornsun-power.com. Packing bag number: 58200013; 2. If the product is not operated within the required load range, the product performance cannot be guaranteed to comply with all parameters in the datasheet; 3. The maximum capacitive load offered were tested at input voltage range and full load; 4. Unless otherwise specified, parameters in this datasheet were measured under the conditions of Ta=25°C, humidity<75%RH with nominal input voltage and rated output load;...