Catalog excerpts
Benefits • Perfect for rental yards, landscapers, golf courses and pruning crews, this high-capacity unit is easy to transport and operate. • The only chipper in its class to combine both a wide infeed chute opening and 1 ¼" thick chipping disc, the M8D has a 251-pound disc and shaft weight provides more inertia to power through material and continuously feed material. • With a single top feed wheel compression system and 32.3 ci hydraulic motor with spring-assisted down pressure, the M8D generates more than 2,300 lb/ft of material pulling force and approximately 1,000 lb/ft of combined down pressure to easily feed a variety of materials. • Like all Morbark equipment, the M8D is a long-lasting, durable machine backed by a world-class parts and service support team. Belt Drive Infeed Chute Feed System Direct drive with belt power transfer eliminates clutch components and over center belt tensioning systems, reducing problem areas and easing maintenance burdens. Infeed chute with 96-cubic-inch throat opening allows for easy material feeding and reduced trim labor and folds to reduce transport and storage length. 360° swivel discharge with adjustable chip deflector puts chips right where they’re needed without removing the Beever from the tow vehicle. A top feed wheel compression system with spring-assisted down pressure easily breaks down a variety of materials. Specifications may vary with equipment options 5/14/12 Equipment Highlights Additional Features Chipping capacity . . . . . . . . . . . . . . . . . . . . 8" Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7'4" Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5'3" Length (transport) . . . . . . . . . . . . . . . . 12'3 ½" Length (operating) . . . . . . . . . . . . . . . . . . 14'3" Gross weight . . . . . . . . . . . . . 2,150–2,750 lbs. Suspension . . . . . . . . . . . . . . . 2,000 lb. torsion Infeed opening . . . . . 33 ½" wide x 24 ¼" high Throat opening . . . . . . . . . . 12" wide x 8" high Feed wheel . . . . . . . 11 ½" wide x 9" diameter Disc dimensions . . . 1 ¼" thick x 28" diameter Engine . . . . . . . . . . . . . . . . . . Kohler or Kubota Horsepower . . . . . . . . . . . . . . . . . . . 35–44 HP Fuel capacity . . . . . . . . . . . . . . . . . . 10 gallons Hydraulic capacity . . . . . . . . . . . . . . 10 gallons Frame . . . . . . . . . . . . . . . . . . . . 2" x 4" Tubular Tires . . . . . . . . . . . . . . . . . . . (2) 185/80Rx14" Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . 2" Ball Direct drive with belt power transfer Fuel tank sight gauge, drain plug and shut‑off valve Automatic feed system Chipper disc with two 10 ½" x 4" x 3/8" dual‑edged chipper knives and four full-length, bolt-on, chip throwing paddles Hydraulic tank shut-off valve, drain plug, clean-out cover and vented filter head assembly with dipstick to check oil level Reversible feed works control bar and dual safety cables located within infeed chute Pinned chipper hood access with integrated hood safety device to disconnect the start system when the chipper hood is opened and allow ease of disc maintenance. Variable speed flow control 2,500 lb. Torflex suspension axle with electric brake system, electric brake actuator and 185R14 tires with rims Custom paint and logo packages 2 ½" lunet ring Knife saver tool Engine stop on infeed Material pushing tool Spanish and English safety decals 3" x 4" tubular steel fixed length drawbar and 3/8" thick safety chains with clasp hooks Morthane Paint System: A chemically cured, electrostatically applied urethane coating with high-gloss finish, built-in UV protection, chip and chemical resistance and corrosion protection
Open the catalog to page 1All Morbark catalogs and technical brochures
-
1300B TUB GRINDER
2 Pages
-
1600 TUB GRINDER
2 Pages
-
2131
2 Pages
-
RUSH CHIPPERS
22 Pages
-
23X series
1 Pages
-
MORBARK® 50/48X
1 Pages
-
640 Debarker
1 Pages
-
DeNubber Debarking Head
1 Pages
-
C Series Debarker
1 Pages
-
PSP Pole and Post Peeler
1 Pages
-
48″ & 58″ Chip Pacs
1 Pages
-
1300 VMill
1 Pages
-
Trough-Type Conveyor
1 Pages
-
Stac-Trac 1000
1 Pages
-
Green Chains
1 Pages
-
Mulch Hog
1 Pages
-
40/36 NCL WHOLE TREE CHIPPER
1 Pages
-
30-36B WCL
1 Pages
-
MORBARK ® DRUM CHIPPER
6 Pages
-
Morbark Beever M12R
1 Pages
-
Morbark Beever M12D
1 Pages
-
Morbark Beever M6R
1 Pages
-
D76 track stump grinder
1 Pages
-
D86 track stump grinder
1 Pages
-
MORBARK 640 LOG DEBARKER
1 Pages
-
CHIP SCREENS
1 Pages
-
CHIP-PACS
1 Pages
-
C-SERIES DEBARKERS
1 Pages
-
PS8 POST PEELER
1 Pages
-
1300 V-MILL
1 Pages
-
through type conveyor
1 Pages
-
MATERIAL HANDLING CONVEYOR
1 Pages
-
BARN SWEEP CONVEYOR
1 Pages
-
1000 . STAC . TRAC
1 Pages
-
LIVE DECKS
1 Pages
-
CHIP BLOWERS
1 Pages
-
CIRCULAR CHOP SAW
1 Pages
-
MORBARK GREEN CHAIN
1 Pages
-
MODEL . HD-30 . MULCH . HOG
1 Pages
-
MORBARK® BEEVER™
6 Pages
-
1200XL Tub Grinder
1 Pages
-
Vibrating Conveyors
1 Pages
-
Stationary Chippers
1 Pages
-
628 Debarker
1 Pages
-
20 NCL Chiparvestor
1 Pages
-
2355 Flail Chiparvestor
1 Pages
-
5500 Stand-Alone Flail
1 Pages
-
25/36 NCL Drum Chipper
1 Pages
-
4600XL Wood Hog
1 Pages
-
D52SPH Stump Grinder
1 Pages
-
7600B Wood Hog
1 Pages
Archived catalogs
-
1300B Tub Grinder
1 Pages
-
Morbark Beever M6R
1 Pages
-
Entire Sawmill Product Guide
20 Pages
-
Predator Shredder
1 Pages
-
Electric Powered Units
3 Pages
-
1600 Tub Grinder
1 Pages