EHHBE-TH3
8Pages

Catalog excerpts

4 flutes high efficiency ball end mill EHHBE-TH3 Epoch High Hard Ball-TH3

Evolved by addopting a TH3 coating on 4-flute ball end mill for high hardened steel processing. On high-hardened steel processing, to achieve even longer tool life. Features of EHHBE-TH3 Highly efficient cutting with 4 flutes Special edge shape in tip area improves cutting performance. TH3 Coating provides long tool life even on hardened steels. Variable Pitch geometry enables vibrations to be suppressed even for 4 flutes. Wide chip pocket improves chip removal. Available for high-efficiency side milling. Applicable range Carbon steel Stainless steel Pre-hardened Hardened steel Hardened...

Open the catalog to page 2

Suppressed vibration with Variable Pitch geometry 4 flutes Variable Pitch X direction Y direction Z direction 4 flutes Equal pitch X direction Y direction Z direction The vibration can be observed a cycle per flute. EHHBE-TH3 exhibits the performance during roughing to semi-finishing of high hardened steel (55HRC∼). ed st Hardened steel (HRC) 70 6 flutes, Epoch High Hard Radius-TH3 4 flutes, Epoch High Hard Ball-TH3 2 flutes, Epoch Deep Ball Evolution Hard-TH3 Newly developed coating "TH3" for hardened steel machining Coating structure ・High hardness coating with excellent wear resistance...

Open the catalog to page 3

For regrinding of this tool, please ask our company. We will reproduce the special tip section shape. O Re-grinding compatibility range table

Open the catalog to page 4

For work materials with hardnesses up to 55HRC, we recommend our company's 2-flute or 3-flute tool series. [Note] ® Use the appropriate coolant for the work material and machining shape. © Use as highly rigid and accurate machine as possible. © These conditions are for general guidance; in actual machining conditions adjust the parameters according to your actual machine and work-piece conditions. ® If the rpm available is lower than that recommended please reduce the feed rate to the same ratio.

Open the catalog to page 5

[Note] ® Use the appropriate coolant for the work material and machining shape. © Use as highly rigid and accurate machine as possible. © These conditions are for general guidance; in actual machining conditions adjust the parameters according to your actual machine and work-piece conditions. @ If the rpm available is lower than that recommended please reduce the feed rate to the same ratio. Cold tool steel cutting example [SLD, 60HRC] """ c? y Size :30x60x5mm Machining time : 10min

Open the catalog to page 6

g pp 02 Cutting application for Laser metal deposition [SKD61Ⓗ 56HRC] ■ Condition for tool wear (after machining) Laser metal deposition part After machining Ma h n n ti e 5min Machining time 35min. Machining time 35min. min. n Base material After machining Work size： 150×150×150mm Work material Base material：SKD61 43HRC Laser metal deposition part： SKD61 56HRC Machine tool : Okuma Corporation MU-8000V LASER EX CAM : C&G SYSTEMS INC. CAM-TOOL Process Laser metal deposition part Rouging Finishing Ma h n n ti e 8min Machining time 58min. Machining time 58min. in. n Cutting speed Microwear and...

Open the catalog to page 7

The diagrams and table data are examples of test results, and are not guaranteed values. "Epoch" and “ ” are registered trademarks of Mitsubishi Hitachi Tool Engineering, Ltd. in Japan. Attentions on Safety 1. Cautions regarding handling (1) When removing the tool from its case (packaging), be careful that the tool does not pop out or is dropped. Be particularly careful regarding contact with the tool flutes. (2) When handling tools with sharp cutting flutes, be careful not to touch the cutting flutes directly with your bare hands. 2. Cautions regarding mounting (1) Before use, check the...

Open the catalog to page 8