Easy cut multi function mill : AHJ type For machining pre-hardened steel or tempered steel Patent Pending For high-efficient machining of mild steel Introducing new JP/JS coating Fusion of "easy cutting geometry" and "multi function geometry" Plunge contouring Deep cutting N Nimble high-efficiency processing p

Regular flute Straight Shank type Item Code ODDD—H Item Code ♦$S ^JitJt? Short flute H^^Rap Maximum flute length Item Code ODDD—H Item Code

Easy cut multi function mill: AHJ type iS/l^-^'T? Modular type Type Item Code ffiffl-l'Vtf—h Inserts BSD-K Item Code «« 3< 1 : Please refer to the attention © of Carbide Shank (P5).

[Note] When using the insert with re ^2.0, it is necessary to carry out additional processing of cutter body corner part. 0EP : WMfcMaaT!1^o Stocked Items. MEP : S;iSSpp"J!^"o No Mark: Manufactured upon request only. "A'EP : iffiSooffl^^ftKooT"S"o "A': Stocked Items Of New products. [ ] ■ Jl5^ffl<!l[W] ly^fM^felX'tfcfeJIiPll^fc 0^"fethja [ ]• Since the same material is not used for the bottom flute, it is not recommended : (fjyZl) rtlJSSXJfiJBil^yil.^-SJUO-Y Vtt— MSfflijTJr'S'o^ : Numbers in parentheses are the number of inserts when using a short flute and Modular Mill.

Easy cut multi function mill: AHJ type Special Shanks for Modular Mills Carbide Shank Item Code Cutter body I ED : H^ttKiSTf o • : Stocked Items. litM] ®-Xz£-Xt (P3)£-tZ-y hT'ISffl"9'3 2:=F/£#'26y^'tiA/o ©When«2 and«1 (pp. 3) are used together as a set, there is no interference. (DrtJIS©5- U y V y fl&li<st>7j\.ll/£ —CTlSfflTS^'S'o ©Commercial milling chucks or shrink-fit holders can be used. © ( ) \t;S&, ABPFM/ARPFM/BCFMlifJW-Bi ZmLZt, ©Dimensions in parentheses are when ABPFM, ARPFM or BCFM is attached. ©<04O> \t;SU, S?SL±JLS$ 200m mtiT* ISC i'ffifflT^C^o ©For the 040 size, it is recommended...

B-p-^y BType Item Code Cutter body •ED : «*ffl<STt" o • : Stocked Items. [>£«] ©FBBfi© S-U^t^ CTffiiTt * To © ( ) ^>Stt, ABPFM/ARPFM/BCFM SStfJtt Bfl U * f. [Note] ©Commercial milling chucks can be used. ©Dimensions in parentheses are when ABPFM, ARPFM, or BCFM is attached. For neck section or total length, additional machining to user specifications is possibli Item Code Cutter body •ED : «*ffl<STt" o • : Stocked Items. [>£«] ©FBBfi© S-U^t^ CTffiffl. © ( ) ABPFM/ARPFM/BCFM SStfJtt Bf U * f. [Note] ©Commercial milling chucks can be used. ©Dimensions in parentheses are when ABPFM, ARPFM, or BCFM...

Easy cut multi function mill: AHJ type I ^Z/3.Z7—^JUffly7—A Modular Mill Arbor For neck section, additional machining to user specifications is possible For neck section, additional machining to user specifications is possible Item Code Cutter body Item Code Cutter body • ED : aspSWS'Ct. • : Stocked Items. MED : SiiSfiSTf. No Mark: Manufactured upon request only @Li,U<D( )^)Sl*,ABPFM/ARPFM/BCFMMtJnf*=SUS-?-. [Note](l)When using the BT30 arbor for modular mills, determine the processing conditions using the standard cutting conditions table as a general guide. If vibrations are a concern due to...

Recommended cutting conditions Cutting conditions for shoulder milling ■ Full 2 inserts are used up to the cutting depth &a. ■ If &a is exceeded, depending on the overlap relationship, a single insert region may occur. Care should be taken regarding the relationship between cutting depth and feed rate. ■ In general, insert damage tends to become larger at the border region of the cut. When using for deep cutting, it is recommended that the cutting depth be set so that two inserts will be used at the cutting border region. [jijft] M:J&[&W]&<ty:M c^(t_?i^L'"C~Fc^U^o [Note] For short flute type,...

Easy cut multi function mill: AHJ type • When the amount the tool sticks out is large, chattering vibrations, etc. are more likely to occur, making cutting conditions unstable. Since this may result in abnormal damage and cause shortened tool life, refer to the factors in the table at right and reduce the cutting width ae when machining. • When using a modular carbide shank with a tool overhang of 5Dc or more, set the conditions by multiplying cutting speed vc by a factor of 0.7 to 0.5.

Recommended cutting conditions Cutting condition for slotting. ■ Refer to the cutting conditions for shoulder milling and set the feed rate to 70% of the value as general criteria. ■ It is recommended that the cutting depth be set within the full 2 inserts region &a. Cutting condition for ramping • Refer to the cutting conditions for shoulder milling and set the feed rate to 70% of the value as general criteria. ■ When cutting steel, it is recommended that the ramp angle 8 is 3 0 or less. With angles larger than this there is a danger of the cut chips not breaking off and sticking to the tool...

Easy cut multi function mill: AHJ type Cutting condition for plunging Refer to the cutting conditions for drilling and set feed rate at 150% to 180% as general criteria. Step feed is not necessary. Pick feed pf£0.5Dc; Refer to the table below for diametrical cutting amount ae.

Advanced high-rake geometry combines easy cut and edge strength. A multi-function end mill with a bottom flute to allow unlimited horizontal and vertical cutting with a single tool. Perform drilling without a pilot hole, ramping or horizontal milling, etc. Since advanced high-rake geometry Increasing rigidity compared with comventional by using special steel and chip pocket geometry. Expands application range. Reduces cutting vibrations and enables stable cutting even when processing with long overhang. Coolant through is aveilable. Cutting force is reduced by high rake geometry. In various corner...