Quick and easy setup The new invisible splice for light duty belts

Our products and solutions meet your needs 70 years of experience and innovation for you SOLUTIONS FOR HEAVY AND LIGHT-DUTY BELTS, MANUFACTURER OF TECHNICAL BELTS, TOOLS, VULCANIZING PRESSES

The flexible splice for light duty PVC / PU belt A solution of flexible splice for light duty belts! IFS (Invisible Flexible Splice) is an innovative and fast solution for splicing your light duty belts. The IFS is the new splicing system for light duty belts, heir to the PVC / PU splice. It has been developed by the MLT team to offer a solution to your daily problems. MLT: always at the forefront of innovation and consistently improving our products inspired by your experienced feedback. Waterproof Flexible Resistant even in severe conditions Integrates perfectly into the belt Manufactured and...

The new IFS tested in extreme situations Tested in severe conditions : As resistant as the previous version Tested in extreme conditions for 1000 hours, 24/24, 7/7, on a fast running conveyor (180 m / min), the result was a high-strength mechanical splice. This occurred even at temperatures up to 85 ° C. A new design created to meet all your needs: But without extra thickness The perfect thickness of the new IFS in the belt gives it an incredible level of integration.

A new range of flexible spl A simple choice for all of your needs For this new generation of flexible splices, we have simplified the range for more efficiency and ease of ordering the product. No longer are there dozens of product designations, the new IFS is broken down into only 4 levels of thickness, covering the majority of belts and most applications! The IFS splice is 1170 mm (46’’) in length when delivered Choose your IFS efficiently and easily: Tension Belt thickness (mm) Choose your IFS in the product range below: Without With With With With Belt thickness With With With Sliding bed...

Here’s how MLT recommends you install the IFS successfully For any length longer than 1.2m, the offset of the IFS can IFS 1 may cause difficulties in inserting the pins. IFS 2 In this case, install your IFS based on the 1st diagram. For an optimal installation of our IFS, we recommend: • A thermofusion temperature for IFS PU Light blue = 150°C • A thermofusion temperature for other IFS = 170°C IFS 1 Splice choice : 1| Check the thickness of the belt and choose the correct splice. Belt preparation: Splice preparation: 3| Remove the acetal pins, put the stainless steel pins 2| Open the belt at...

5| Wedge the edges of the splice and belt with a piece of belt. 6| Cover with the upper die and a stiff plate. Close the press. 7| Set the parameters heating and cooling according to the requirements of the belt. 8| At the conclusion of the heating cycle, repeat on the other end. Consult technical documentation of the supplier. MLT proscribes the vulcanization of the splice in 1 splice. The IFS junction itself should not be heated when thermofusing the IFS with the belt. 9| Remove the stainless steel pins (optional: cut the edges of the splice). 10| Replace the acetal or stainless steel pins...

To follow all MLT news, don't forget to subscribe to our social media networks! Subscribe @mltlacing @minetlacing Access to all of the MLT product installation tutorials in one click! + Follow MLT Minet Lacing Technology

MLT – it’s also metallic fasteners, flexible splices, tools, endless and spliceless technical belts ISC® belt Super-Screw® FIX’N GO® Innovative products, easy to install ! Clip’N Lock® Technical belt Endless spliceles

MLT Minet Lacing Technology SA ZI du Clos Marquet Tél: + (33) 4 77 22 19 19 Rue Michel Rondet - CS 70059 Fax: +(33) 4 77 22 56 43 42 400 St Chamond [email protected] France www.mlt-lacing.com MLT, it’s solutions for heavy and light duty belts, tools, technical belts, etc.